Edco Floor Stripper Ts8 75L 2017 Power Cord Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes - 1 hour

Sections

Safety Precautions
1 step
Power Cord Removal
18 steps
Power Cord
7 steps

Flags

BackEDCO Floor Stripper TS8-.75L (2017)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Safety precautions

Before you begin, ensure the device is powered down and cool to the touch.
Ensure the machine is unplugged.
Turn the power switch counterclockwise into the OFF position.

Before you begin, ensure the device is powered down and cool to the touch.

Ensure the machine is unplugged.

Turn the power switch counterclockwise into the OFF position.

1024

Step 2

              Remove the screw from the red knob

Use a Phillips screwdriver to remove the screw from the center of the red on/off knob.

Use a Phillips screwdriver to remove the screw from the center of the red on/off knob.

Step 3

              Remove the knob

Remove the red knob.
This component is keyed. During reassembly, ensure it is reinstalled in the correct orientation.

Remove the red knob.

This component is keyed. During reassembly, ensure it is reinstalled in the correct orientation.

Step 4

              Remove the black cap

Remove the black plastic cap from the center of the switch assembly.
This component is keyed. During reassembly, ensure it is reinstalled in the correct orientation.

Remove the black plastic cap from the center of the switch assembly.

Step 5

Use a Phillips screwdriver to remove the two screws securing the yellow switch guide to the switch assembly.
During reassembly, ensure this component is installed in the same orientation, with the circle in the 6 o’clock OFF position.

Use a Phillips screwdriver to remove the two screws securing the yellow switch guide to the switch assembly.

During reassembly, ensure this component is installed in the same orientation, with the circle in the 6 o’clock OFF position.

Step 6

Remove the yellow switch guide from the switch assembly.
Remove the black plastic spacer from underneath the yellow switch guide.

Remove the yellow switch guide from the switch assembly.

Remove the black plastic spacer from underneath the yellow switch guide.

Step 7

              Remove the upper switch housing

Use a Phillips screwdriver to remove the four screws securing the upper half of the switch housing to the lower half.
These screws may not come out of their recesses in the housing once they are completely unthreaded. If some stay inside once loose, don’t lose track of them.

Use a Phillips screwdriver to remove the four screws securing the upper half of the switch housing to the lower half.

These screws may not come out of their recesses in the housing once they are completely unthreaded. If some stay inside once loose, don’t lose track of them.

Step 8

Lift the upper half of the switch housing off of the lower half."
The rubber gasket may fall out of the upper housing during the removal process. Do not forget to reinstall the gasket upon reassembly.

Lift the upper half of the switch housing off of the lower half."

The rubber gasket may fall out of the upper housing during the removal process. Do not forget to reinstall the gasket upon reassembly.

Step 9

              Disconnect the power cord from the frame

Use a 3/8 inch socket to remove the bolt securing the power cord loom clamp to the switch bracket.

Use a 3/8 inch socket to remove the bolt securing the power cord loom clamp to the switch bracket.

Step 10

              Remove the loom clamp

Remove the loom clamp from the power cable.

Remove the loom clamp from the power cable.

Step 11

              Remove the switch housing

Use a socket to remove the four 11/32 inch nuts from the on/off switch bracket.
During reassembly, use a Phillips screwdriver in combination with the 11/32 inch socket wrench to tighten the bolts securing the switch to the bracket."

Use a socket to remove the four 11/32 inch nuts from the on/off switch bracket.

During reassembly, use a Phillips screwdriver in combination with the 11/32 inch socket wrench to tighten the bolts securing the switch to the bracket."

Step 12

Lift the switch assembly off of the switch bracket.
The switch housing bolts may fall out when you remove the housing.

Lift the switch assembly off of the switch bracket.

The switch housing bolts may fall out when you remove the housing.

Step 13

              Disconnect the green wires

Use a flathead screwdriver to remove the screw securing the two green ground wires to the switch housing.

Use a flathead screwdriver to remove the screw securing the two green ground wires to the switch housing.

Step 14

Separate the green ground wires from each other and move them away from the switch housing.

Separate the green ground wires from each other and move them away from the switch housing.

Step 15

              Disconnect the power cord from the switch

Use a flathead screwdriver to loosen the two screws on the right side of the switch assembly securing the black and white wires from the power cord.
During reassembly, ensure each wire is installed in its correct location on the switch.

Use a flathead screwdriver to loosen the two screws on the right side of the switch assembly securing the black and white wires from the power cord.

During reassembly, ensure each wire is installed in its correct location on the switch.

Step 16

Remove the black wire from the switch.

Remove the black wire from the switch.

Step 17

Remove the white wire from the switch.

Remove the white wire from the switch.

Step 18

Use a 1-1/16 inch wrench or an adjustable wrench to loosen the power cord’s strain relief fitting from the switch housing.
Once the fitting is loose enough to turn by hand, twist the power cord and fitting counterclockwise until it is fully unthreaded from the switch housing.

Use a 1-1/16 inch wrench or an adjustable wrench to loosen the power cord’s strain relief fitting from the switch housing.

Once the fitting is loose enough to turn by hand, twist the power cord and fitting counterclockwise until it is fully unthreaded from the switch housing.

Step 19

              Remove the power cord

Remove the power cord from the on/off switch.

Remove the power cord from the on/off switch.

Step 20

              Transfer the strain relief fitting to the new cord

If the replacement power cord comes with a strain relief fitting pre-installed, skip the remaining steps and begin reassembly
Use two adjustable wrenches to unscrew the strain relief fitting by turning the locknut counterclockwise relative to the fitting.
1-1/16 inch lock nut
15/16 inch strain relief fitting
Reassembly tip: note the length from the end of the power cord to the strain relief fitting. Match this length as close as possible when reinstalling the fitting.

If the replacement power cord comes with a strain relief fitting pre-installed, skip the remaining steps and begin reassembly

Use two adjustable wrenches to unscrew the strain relief fitting by turning the locknut counterclockwise relative to the fitting.

1-1/16 inch lock nut

15/16 inch strain relief fitting

Reassembly tip: note the length from the end of the power cord to the strain relief fitting. Match this length as close as possible when reinstalling the fitting.

Step 21

Remove the lock nut from the power cord.

Remove the lock nut from the power cord.

Step 22

Insert a flathead screwdriver into the fitting and push the blue grommet out to remove it from the housing.

Insert a flathead screwdriver into the fitting and push the blue grommet out to remove it from the housing.

Step 23

Remove the fitting from the power cord.

Remove the fitting from the power cord.

Step 24

Remove the grommet from the power cord.

Remove the grommet from the power cord.

Step 25

Remove the remaining nut and washer from the power cable.
These may have slid down the power cable during the previous steps.

Remove the remaining nut and washer from the power cable.

These may have slid down the power cable during the previous steps.

Step 26

Only the power cord remains.

Only the power cord remains.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Robert Boyd

Member since: 02/01/2021

21,303 Reputation

                                      92 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges

Introduction#

What you need#

Introduction

What you need