Difficulty
Difficult
Steps
16
Time Required
25 - 30 minutes
Sections
4
- Battery
- 5 steps
- Front Bumper
- 4 steps
- Bottom Case
- 2 steps
- Vacuum Motor
- 5 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackEcovacs Deebot 900
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove all the brushes from the Deebot.
Remove all the brushes from the Deebot.
1024
Step 2
- Using a Phillips #0 screwdriver, remove the two 12.25 mm screws holding the battery cover in place.
Using a Phillips #0 screwdriver, remove the two 12.25 mm screws holding the battery cover in place.
Step 3
- Remove the battery cover.
Remove the battery cover.
Step 4
- Using the two white straps on the sides of the battery, gently remove the battery.
- Be careful not to rip out the battery cable.
Using the two white straps on the sides of the battery, gently remove the battery.
Be careful not to rip out the battery cable.
Step 5
- Carefully disconnect the battery cable by pulling near the connector at the bottom of the battery compartment.
Carefully disconnect the battery cable by pulling near the connector at the bottom of the battery compartment.
Step 6
Front Bumper
- Using a Phillips #00 screwdriver, remove the eight screws on the bottom edge of the bumper.
Using a Phillips #00 screwdriver, remove the eight screws on the bottom edge of the bumper.
Step 7
- Remove the black strip on the bottom of the bumper.
Remove the black strip on the bottom of the bumper.
Step 8
- Carefully lift up the bumper untill it pops out of place.
Carefully lift up the bumper untill it pops out of place.
Step 9
- Disconnect the two cables connecting the bumper to the body of the Deebot.
- Remove the front bumper from the device.
Disconnect the two cables connecting the bumper to the body of the Deebot.
Remove the front bumper from the device.
Step 10
Bottom Case
- Using a Phillips #00 screwdriver, take out the six screws around the perimeter of the bottom case.
Using a Phillips #00 screwdriver, take out the six screws around the perimeter of the bottom case.
Step 11
- Insert a Jimmy into the seam and work all the way around the robot.
- Disconnect the two cables and remove the bottom case from the device.
Insert a Jimmy into the seam and work all the way around the robot.
Disconnect the two cables and remove the bottom case from the device.
Step 12
Vacuum Motor
- Using the Phillips #00 screwdriver, remove the three screws around the laser unit.
Using the Phillips #00 screwdriver, remove the three screws around the laser unit.
Step 13
- Carefully lift the laser unit off of the motor assembly.
Carefully lift the laser unit off of the motor assembly.
Step 14
- Remove the single screw holding the motor assembly in place using the Phillips #00 screwdriver.
Remove the single screw holding the motor assembly in place using the Phillips #00 screwdriver.
Step 15
- Disconnect the ribbon cable holding the assembly in place.
- Be careful not to damage the cable.
Disconnect the ribbon cable holding the assembly in place.
Be careful not to damage the cable.
Step 16
- Lift and remove the motor assembly out of the Deebot.
Lift and remove the motor assembly out of the Deebot.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Gillian Blumer
Member since: 01/16/2020
492 Reputation
3 Guides authored
Badges:
10
+7 more badges
Team
Embry-Riddle Aeronautical University, Team S6-G1, Rauch Spring 2020
Member of Embry-Riddle Aeronautical University, Team S6-G1, Rauch Spring 2020
ERAU-RAUCH-S20S6G1
3 Members
17 Guides authored
Aaron Commons - May 2, 2021
Reply
Where can you find a replacement vacuum motor for the zoom 930?
