Eclipse 180G2 Mp3 Video Player Battery Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          20 minutes

Sections

Outer Case
2 steps
Battery
2 steps

Flags

Needs More Images

A few more images would make this guide’s procedures crystal clear.

BackEclipse 180G2-W
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Outer Case

Remove the two screws on the bottom of the device with a Phillips head screwdriver.
Use a spudger to remove the plastic plate from the bottom of the player.

Remove the two screws on the bottom of the device with a Phillips head screwdriver.

Use a spudger to remove the plastic plate from the bottom of the player.

1024

Step 2

              Remove inner circuit from case shell

Hold the device firmly between two fingers. Be sure you aren’t holding down the top of the device; the circuit board will slide out of the shell through that end.
Use the spudger to push the USB port on the bottom of the device inward.
The plastic LCD cover and the key pad will now be free; they were held in place by the tension between the case and the internal circuit board.

Hold the device firmly between two fingers. Be sure you aren’t holding down the top of the device; the circuit board will slide out of the shell through that end.

Use the spudger to push the USB port on the bottom of the device inward.

The plastic LCD cover and the key pad will now be free; they were held in place by the tension between the case and the internal circuit board.

Step 3

              Finding the Battery

The battery is the large packet-like component beneath where the buttons would be.
Gently lift the battery and move it off of the circuit board, allowing access to the wires.

The battery is the large packet-like component beneath where the buttons would be.

Gently lift the battery and move it off of the circuit board, allowing access to the wires.

Step 4

              Separating the Battery

Snip the wires using a wirecutter. Be careful not to nick the battery.

Snip the wires using a wirecutter. Be careful not to nick the battery.

To reassemble your device, follow these instructions in reverse order after you’ve soldered the new battery.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 9 other contributors

                    James Walker

Member since: 01/15/2015

373 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team 1-4, Tanski Winter 2015                        

                                                  Member of USF Tampa, Team 1-4, Tanski Winter 2015 



                    USFT-TANSKI-W15S1G4                     


                                            4 Members                     


                                            5 Guides authored

Tom - Jul 7, 2015

What kind of battery is it? And where do you get a new battery?

JBreezy - Nov 12, 2015

Its a button cell battery like 1for a watch and Wal-Mart Walgreen riteaid should have it

Martin Willcocks - Jan 7, 2018

You should specify the battery type. The plastic wrap on the photo shows 180mAh capacity and it has to be rechargeable, unlikely to be lead-acid and therefore should not leak acid. Button cell batteries aren’t usually rechargeable so please explain exactly what battery type you used - manufacturer, model no. etc. Since you suggest cutting the wires, how do you reconnect to the new battery? The photo is inadequate to show how this is done. If the battery is a replaceable button cell, I would not expect it to be in an apparently sealed plastic bag.

Aayush - May 7, 2019

Since you suggest cutting the wires, how do you reconnect to the new battery? The photo is inadequate to show how this is done. If the battery is a replaceable button cell, I would not expect it to be in an apparently sealed plastic bag.

https://www.alltechnerd.com/html5-video-…

Electronics Overhaul - Jun 12, 2019

It’s a 502025 Li-Po battery. Capacity doesn’t matter, but you can find them at 200mAh. The replacement batteries come with wires.

Needs More Images#

Introduction#

What you need#

#

#

#

#

#

#

Team#

#

Needs More Images

Introduction

What you need

Team