Difficulty

Moderate

Steps

8

Time Required

                          15 - 30 minutes

Sections

4

  • Spark Plug Disconnect
  • 1 step
  • Control Handle Assembly
  • 2 steps
  • Control Handle Disassembly
  • 2 steps
  • Flexible Tube
  • 3 steps

Flags

0

  • BackEcho Power Pruner, 25.4 cc PPT-2620 (2019)

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disconnect the spark plug
  • Move the stop switch into the “stop” position to turn the pruner off before attempting any repairs.
  • Pull the spark plug cap straight off of the spark plug.

Move the stop switch into the “stop” position to turn the pruner off before attempting any repairs.

Pull the spark plug cap straight off of the spark plug.

1024

Step 2

              Remove the control handle assembly
  • Use a T25 Torx screwdriver to loosen (but not remove) the two screws clamping the main pipe assembly to the control handle.

Use a T25 Torx screwdriver to loosen (but not remove) the two screws clamping the main pipe assembly to the control handle.

Step 3

  • Remove the control handle from the main pipe assembly.

Remove the control handle from the main pipe assembly.

Step 4

              Disassemble the control handle
  • Use a T25 Torx screwdriver to remove the seven screws holding the control handle together.

Use a T25 Torx screwdriver to remove the seven screws holding the control handle together.

Step 5

  • Lift the top half of the control handle straight up to remove it.
  • The following step shows the throttle trigger and throttle lockout removed. These parts do not need to be removed for this guide.

Lift the top half of the control handle straight up to remove it.

The following step shows the throttle trigger and throttle lockout removed. These parts do not need to be removed for this guide.

Step 6

              Remove the control handle
  • Use a T25 Torx screwdriver to loosen (but don’t remove) the screw clamping the strap hook to the handle pipe.
  • You may need an 8 mm socket and socket wrench to hold the nut on the back of the strap hook while you loosen the bolt.
  • Remove the two T25 screws securing the handle to the handle pipe.

Use a T25 Torx screwdriver to loosen (but don’t remove) the screw clamping the strap hook to the handle pipe.

You may need an 8 mm socket and socket wrench to hold the nut on the back of the strap hook while you loosen the bolt.

Remove the two T25 screws securing the handle to the handle pipe.

Step 7

  • Slide the strap hook off the pipe and remove it.
  • Slide both clamps that held the handle off of the pipe and remove them.

Slide the strap hook off the pipe and remove it.

Slide both clamps that held the handle off of the pipe and remove them.

Step 8

              Remove the flexible tube
  • Slide the flexible tube off of the handle pipe and remove it.

Slide the flexible tube off of the handle pipe and remove it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor 


                    Adam O'Camb

Member since: 04/11/2015

173,479 Reputation

                                      418 Guides authored                  



                       Badges:
                       39







                                                        +36 more badges

JANET - Apr 22, 2020

Reply

The photos and instructions are great, but a video on how to dismantle and reassemble would be better. still shots cannot show the nuances of the reassembly.