Echo Brushcutter Srm2620U 2017 Clutch Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          40 minutes - 1 hour

Sections

Safety Precautions
1 step
Clutch Assembly
15 steps

Flags

BackEcho Brushcutter SRM-2620U (2017)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Disconnect the spark plug wire

Before you begin, ensure that the engine is powered down and cool to the touch.
Grip the plastic housing at the end of the spark plug wire and pull firmly to disconnect it.

Before you begin, ensure that the engine is powered down and cool to the touch.

Grip the plastic housing at the end of the spark plug wire and pull firmly to disconnect it.

1024

Step 2

              Disconnect the control cables

Unclip the throttle cable routing clip from the main shaft.

Unclip the throttle cable routing clip from the main shaft.

Step 3

Grip both ends of one of the control cable bullet connectors and pull to disconnect it.
Repeat to disconnect the second control cable connector.
These connectors are interchangeable.

Grip both ends of one of the control cable bullet connectors and pull to disconnect it.

Repeat to disconnect the second control cable connector.

These connectors are interchangeable.

Step 4

              Remove the muffler cover

This Echo device has an included multi-tool with a T30 Torx screwdriver, but any T30 Torx driver is compatible.
Use a T30 Torx driver to remove the two screws securing the muffler cover.

This Echo device has an included multi-tool with a T30 Torx screwdriver, but any T30 Torx driver is compatible.

Use a T30 Torx driver to remove the two screws securing the muffler cover.

Step 5

Lift the muffler cover up and pivot it on its top edge to unlatch it from the engine cover.
Remove the muffler cover.

Lift the muffler cover up and pivot it on its top edge to unlatch it from the engine cover.

Remove the muffler cover.

Step 6

              Remove the engine cover

Use a T30 Torx driver to remove the two screws securing the engine cover.

Use a T30 Torx driver to remove the two screws securing the engine cover.

Step 7

Lift the engine cover straight up to remove it.

Lift the engine cover straight up to remove it.

Step 8

              Remove the fan cover

Use a T30 Torx driver to remove the two screws securing the fan cover.

Use a T30 Torx driver to remove the two screws securing the fan cover.

Step 9

Pull the fan cover away from the motor assembly.

Pull the fan cover away from the motor assembly.

Step 10

              Reassembly tip

During reassembly:
Reroute the two control cables through the opening on the fan cover.
Lay the cables into their slot on the clutch cover.

During reassembly:

Reroute the two control cables through the opening on the fan cover.

Lay the cables into their slot on the clutch cover.

Step 11

              Separate the shaft from the engine assembly

Use a T30 Torx driver to loosen, but not remove, the collar bolt securing the main shaft to the engine assembly.

Use a T30 Torx driver to loosen, but not remove, the collar bolt securing the main shaft to the engine assembly.

Step 12

Grip the engine assembly and pull to remove it from the main shaft.
With the engine assembly removed, take care to not put any strain on the still-connected throttle cable.

Grip the engine assembly and pull to remove it from the main shaft.

With the engine assembly removed, take care to not put any strain on the still-connected throttle cable.

Step 13

              Remove the clutch cover

Use a T30 Torx driver to remove the two screws securing the clutch cover.

Use a T30 Torx driver to remove the two screws securing the clutch cover.

Step 14

Remove the clutch cover.

Remove the clutch cover.

Step 15

              Remove the clutch assembly

Use a 1/2 inch socket to remove the two 12 mm-long bolts and four accompanying washers securing the clutch assembly.
During reassembly:
Note that the larger washer goes underneath the clutch assembly and the small washer goes above.
Ensure that the clutch assembly is reinstalled arrow side up.

Use a 1/2 inch socket to remove the two 12 mm-long bolts and four accompanying washers securing the clutch assembly.

Note that the larger washer goes underneath the clutch assembly and the small washer goes above.

Ensure that the clutch assembly is reinstalled arrow side up.

Step 16

Remove the clutch assembly.

Remove the clutch assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                    Carsten Frauenheim

Member since: 03/10/2020

81,713 Reputation

                                      330 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team