Difficulty

Moderate

Steps

10

Time Required

                          30 - 40 minutes

Sections

3

  • Filter Cover
  • 2 steps
  • Buttons
  • 2 steps
  • Motor
  • 6 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

  • BackDyson Supersonic HD01

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

  • Caution: when working with switches and other fragile components, make sure to be gentle and not forceful in removing and inserting parts and electronics.Reminder: Upon reassembling, a new adhesive will have to be reapplied for the buttons to be replaced onto the dryer.

What you need

Step 1

              Filter Cover
  • Find the red dot along the top of the filter cover.
  • The red dot will be aligned with the white dot at the bottom of the hair dryer’s handle.
  • Twist the filter cover counter-clockwise until the red dot is shifted to align with the white open circle on the dryer handle.

Find the red dot along the top of the filter cover.

The red dot will be aligned with the white dot at the bottom of the hair dryer’s handle.

Twist the filter cover counter-clockwise until the red dot is shifted to align with the white open circle on the dryer handle.

1024

Step 2

  • Remove the air filter by sliding it off the end of the cord.

Remove the air filter by sliding it off the end of the cord.

Step 3

              Buttons
  • Heat the iOpener in the microwave for 30 seconds and apply it immediately to the top of the buttons.
  • Leave the iOpener in place for a couple minutes.

Heat the iOpener in the microwave for 30 seconds and apply it immediately to the top of the buttons.

Leave the iOpener in place for a couple minutes.

Step 4

  • Remove the buttons with tweezers.
  • Power button
  • Cold shot button
  • Use a microfiber towel soaked in rubbing alcohol to clean the button holes. Doing this will loosen the buttons if jammed.

Remove the buttons with tweezers.

Power button

Cold shot button

Use a microfiber towel soaked in rubbing alcohol to clean the button holes. Doing this will loosen the buttons if jammed.

Step 5

              Motor
  • Remove the inner cover from the hair dryer by pulling each end apart to slide down the cover.

Remove the inner cover from the hair dryer by pulling each end apart to slide down the cover.

Step 6

  • Pull down the cover of the hair dryer.

Pull down the cover of the hair dryer.

Step 7

  • Pop off the front panel of the hair dryer.
  • Flip the hair dryer 180 degrees to the back panel.
  • Remove the three 10 mm screws located on the back of the hair dryer using a T3 Torx screwdriver.

Pop off the front panel of the hair dryer.

Flip the hair dryer 180 degrees to the back panel.

Remove the three 10 mm screws located on the back of the hair dryer using a T3 Torx screwdriver.

Step 8

  • Flip the hair dryer back to the front panel.
  • Remove the four 10 mm screws on the front using a T4 Torx screwdriver.
  • Remove the back cover of the hair dryer.

Flip the hair dryer back to the front panel.

Remove the four 10 mm screws on the front using a T4 Torx screwdriver.

Remove the back cover of the hair dryer.

Step 9

  • Slide down the cover of the motor.
  • Disconnect the switch on the metal circular area towards the center of the motor.

Slide down the cover of the motor.

Disconnect the switch on the metal circular area towards the center of the motor.

Step 10

  • Disconnect the switch located in the center area of the motor.
  • Slide off the black sheath on the motor.

Disconnect the switch located in the center area of the motor.

Slide off the black sheath on the motor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Sophie Windover

Member since: 09/26/2022

317 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Utah Tech University, Team 1-5, McMurrin Fall 2022                        

                                                  Member of Utah Tech University, Team 1-5, McMurrin Fall 2022 



                    UTAHTECH-MCMURRIN-F22S1G5                     


                                            3 Members                     


                                            3 Guides authored