Dyson Dc58 Main Body Replacement Repair Guide

Difficulty

Moderate

Steps

7

Time Required

                          5 minutes            

Sections

2

• Bin
• 4 steps
• Main Body
• 3 steps

Flags

1

Missing Prerequisites

This guide is missing information on how to start the process. Make a prerequisite guide!

• BackDyson DC58

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Video Overview

Step 1

              Bin               

• Make sure your vacuum is unplugged.
• Avoid pressing the red trigger on the vacuum handle; this will power on the vacuum.

Make sure your vacuum is unplugged.

Avoid pressing the red trigger on the vacuum handle; this will power on the vacuum.

1024

Step 2

• Locate the red lever parallel to the red trigger and on the side of the clear bin.

Locate the red lever parallel to the red trigger and on the side of the clear bin.

Step 3

• Push the red lever downward to open the clear bin. You may need to do this over a trash bin if there is debris in the clear bin.

Push the red lever downward to open the clear bin. You may need to do this over a trash bin if there is debris in the clear bin.

Step 4

• Push the red lever downward again while pulling the clear bin away from the main body of the Dyson vacuum.

Push the red lever downward again while pulling the clear bin away from the main body of the Dyson vacuum.

Step 5

              Main Body               

• Flip the vacuum over so that the silver cyclone part of the vacuum is now at the base.

Flip the vacuum over so that the silver cyclone part of the vacuum is now at the base.

Step 6

• Locate the two visible white clips seen between the main body and the purple cyclone of the vacuum.
• Use tweezers to pinch the two visible white clips together.
• It may require a few tries to pinch the clips since the space between the main body and cyclone is small.

Locate the two visible white clips seen between the main body and the purple cyclone of the vacuum.

Use tweezers to pinch the two visible white clips together.

It may require a few tries to pinch the clips since the space between the main body and cyclone is small.

Step 7

• Tilt and pull the main body away from the purple cyclone of the vacuum.
• You may hear a loud snap when the cyclone is released from the main body, this is to be expected.

Tilt and pull the main body away from the purple cyclone of the vacuum.

You may hear a loud snap when the cyclone is released from the main body, this is to be expected.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      12 other people completed this guide.                                             

Author

                                      with 6 other contributors 

                    Krista St Onge                     

Member since: 09/17/2015

2,068 Reputation

                                      2 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges                           

Team

                       CSU Fullerton, Team 2-4, Bruce Fall 2015                        

                                                  Member of CSU Fullerton, Team 2-4, Bruce Fall 2015 



                    CSUF-BRUCE-F15S2G4                     


                                            4 Members                     


                                            17 Guides authored                     

Jason - Dec 14, 2017

Reply

Mine ended up dismantled after it had been dropped. Couldn’t get it back together until I read the bit about the tweezers /(pliers) and the white clips. It does not push in with out squeezing them first

chrisashton1 - Jul 28, 2018

Reply

Has anyone replaced the red release catch?

Anton Simonov - Dec 21, 2018

Reply

The white C-ring with clips must be pushed down in order to reassemble device. Takes some time to practice.

t_picano - Jan 17, 2021

Reply

I’m trying to figure out how to put spring and plastic pieces back in on the inside of red lever on motor body?? Any help I’d really appreciate ?