Difficulty

Moderate

Steps

10

Time Required

                          4 minutes

Sections

3

  • Bin
  • 4 steps
  • Main Body
  • 3 steps
  • Cyclone
  • 3 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackDyson DC58

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Bin
  • Make sure your vacuum is unplugged.
  • Avoid pressing the red trigger on the vacuum handle; this will power on the vacuum.

Make sure your vacuum is unplugged.

Avoid pressing the red trigger on the vacuum handle; this will power on the vacuum.

1024

Step 2

  • Locate the red lever parallel to the red trigger and on the side of the clear bin.

Locate the red lever parallel to the red trigger and on the side of the clear bin.

Step 3

  • Push the red lever downward to open the clear bin. You may need to do this over a trash bin if there is debris in the clear bin.

Push the red lever downward to open the clear bin. You may need to do this over a trash bin if there is debris in the clear bin.

Step 4

  • Push the red lever downward again while pulling the clear bin away from the main body of the Dyson vacuum.

Push the red lever downward again while pulling the clear bin away from the main body of the Dyson vacuum.

Step 5

              Main Body
  • Flip the vacuum over so that the silver cyclone part of the vacuum is now at the base.

Flip the vacuum over so that the silver cyclone part of the vacuum is now at the base.

Step 6

  • Locate the two visible white clips seen between the main body and the purple cyclone of the vacuum.
  • Use tweezers to pinch the two visible white clips together.
  • It may require a few tries to pinch the clips since the space between the main body and cyclone is small.

Locate the two visible white clips seen between the main body and the purple cyclone of the vacuum.

Use tweezers to pinch the two visible white clips together.

It may require a few tries to pinch the clips since the space between the main body and cyclone is small.

Step 7

  • Tilt and pull the main body away from the purple cyclone of the vacuum.
  • You may hear a loud snap when the cyclone is released from the main body, this is to be expected.

Tilt and pull the main body away from the purple cyclone of the vacuum.

You may hear a loud snap when the cyclone is released from the main body, this is to be expected.

Step 8

              Cyclone
  • Use the metal spudger placed between the black rim and the purple rim to separate the purple screen cover from the cyclone body.
  • Pry all the way around the screen cover.

Use the metal spudger placed between the black rim and the purple rim to separate the purple screen cover from the cyclone body.

Pry all the way around the screen cover.

Step 9

  • Use a T9 screw driver to remove the five 14mm screws around the edge of the cyclone body.

Use a T9 screw driver to remove the five 14mm screws around the edge of the cyclone body.

Step 10

  • Pull down on the black tube-like part of the silver cyclone body to remove it from the cyclone of the Dyson.
  • You may need to wiggle the tube as you are pulling down to loosen the pieces apart.

Pull down on the black tube-like part of the silver cyclone body to remove it from the cyclone of the Dyson.

You may need to wiggle the tube as you are pulling down to loosen the pieces apart.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      18 other people completed this guide.

Author

                                      with 4 other contributors 


                    Herllaine Asistio

Member since: 09/17/2015

215 Reputation

                                      1 Guide authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       CSU Fullerton, Team 2-4, Bruce Fall 2015                        

                                                  Member of CSU Fullerton, Team 2-4, Bruce Fall 2015 



                    CSUF-BRUCE-F15S2G4                     


                                            4 Members                     


                                            17 Guides authored

Don - Dec 6, 2016

Reply

Great job, very useful thanks

robh - Apr 24, 2017

Reply

Fantastic thanks!!!!

macx - May 10, 2017

Reply

Very helpful indeed.

David Parsons - Jun 2, 2018

Reply

Thanks. Had to wash out the dog smell. This did the trick.

Thanks. Had to wash out the dog smell. This did the trick when new filters wouldn’t. Shame on Dyson for not making an easier to clean vacuum.