Difficulty

Moderate

Steps

17

Time Required

                          1 hour

Sections

3

  • Top Cover
  • 3 steps
  • WiFi Antenna
  • 3 steps
  • Motherboard
  • 11 steps

Flags

1

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

  • BackDynex DX-WBRDVD1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Top Cover
  • Remove the four 5mm Phillips #1 screws that connect the black outer shell to the silver back of the device.

Remove the four 5mm Phillips #1 screws that connect the black outer shell to the silver back of the device.

1024

Step 2

  • Remove the two 5mm screws on the left and right side panels.
  • There is one screw on each side that secures the cover to the body of the device.

Remove the two 5mm screws on the left and right side panels.

There is one screw on each side that secures the cover to the body of the device.

Step 3

  • Lift the black cover to a 45 degree angle from the rear of the device and pull the cover away entirely.
  • Check that the power cord is not preventing the device from opening or closing.

Lift the black cover to a 45 degree angle from the rear of the device and pull the cover away entirely.

Check that the power cord is not preventing the device from opening or closing.

Step 4

              WiFi Antenna
  • Use the metal spudger to remove the white clip from the antenna by prying the clip away from the antenna.
  • Use a pointed tool and press down on the indents on both sides of the clip to loosen.

Use the metal spudger to remove the white clip from the antenna by prying the clip away from the antenna.

Use a pointed tool and press down on the indents on both sides of the clip to loosen.

Step 5

  • Remove the two 7mm screws from both sides of the antenna.

Remove the two 7mm screws from both sides of the antenna.

Step 6

  • Slide the antenna inwards and gently remove.

Slide the antenna inwards and gently remove.

Step 7

              Motherboard
  • After removing the antenna, remove the hdmi screw (5mm)
  • Fine threaded

After removing the antenna, remove the hdmi screw (5mm)

Fine threaded

Step 8

  • Remove component screw (7mm)
  • Corse thread

Remove component screw (7mm)

Corse thread

Step 9

  • Lift power cord and move to the side

Lift power cord and move to the side

Step 10

  • Remove the white clip with colored wires from mother board.
  • Use a pointed tool and press in on the sides of the clip to release.

Remove the white clip with colored wires from mother board.

Use a pointed tool and press in on the sides of the clip to release.

Step 11

  • Lift up and out to remove the large white plastic wiring strip. Lift lightly on the back clip holding it to loosen.

Lift up and out to remove the large white plastic wiring strip. Lift lightly on the back clip holding it to loosen.

Step 12

  • Remove the power connection to the motherboard small white clip with 4 white wires coming out.
  • Press sides and pull up the edges with sharp tool

Remove the power connection to the motherboard small white clip with 4 white wires coming out.

Press sides and pull up the edges with sharp tool

Step 13

  • Pull the 1cm white tab straight up and out.
  • The side with exposed wires points towards the face plate.

Pull the 1cm white tab straight up and out.

The side with exposed wires points towards the face plate.

Step 14

  • Pull the larger white 9 pin power cord that connects the power board to the motherboard.

Pull the larger white 9 pin power cord that connects the power board to the motherboard.

Step 15

  • Pull the second white 1cm wide tab between the motherboard and power supply board.
  • The side with exposed wires points towards the disc drive.

Pull the second white 1cm wide tab between the motherboard and power supply board.

The side with exposed wires points towards the disc drive.

Step 16

  • Remove the two 5mm screws that connect the mother board to the device.

Remove the two 5mm screws that connect the mother board to the device.

Step 17

  • Slide board up and out at a slight angle

Slide board up and out at a slight angle

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Harrison Williams

Member since: 04/05/2018

499 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Linn Benton Community College, Team S1-G2, Johnson Spring 2018                        

                                                  Member of Linn Benton Community College, Team S1-G2, Johnson Spring 2018 



                    LBCC-JOHNSON-S18S1G2                     


                                            4 Members                     


                                            6 Guides authored