Difficulty

Moderate

Steps

10

Time Required

Suggest a time??

Sections

3

  • Batteries
  • 2 steps
  • Keyboard
  • 4 steps
  • Wheelhead
  • 4 steps

Flags

1

Missing Details

Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.

  • BackDymo LabelManager 160

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Batteries
  • Place the device face-down to access the battery compartment.

Place the device face-down to access the battery compartment.

1024

Step 2

  • Remove the compartment cover to reveal the batteries. Remove the 6 old batteries.

Remove the compartment cover to reveal the batteries. Remove the 6 old batteries.

Step 3

              Keyboard
  • To open the cartridge compartment, simply lift on the front of the device.

To open the cartridge compartment, simply lift on the front of the device.

Step 4

  • Using a Phillips #0 screwdriver, remove the four 1.3mm screws from the cartridge compartment and two 1.2mm screws from the battery compartment.

Using a Phillips #0 screwdriver, remove the four 1.3mm screws from the cartridge compartment and two 1.2mm screws from the battery compartment.

Step 5

  • Using a spudger or other tool, lift and remove the front of the device. This should be done all around the device to ensure the two parts split correctly.

Using a spudger or other tool, lift and remove the front of the device. This should be done all around the device to ensure the two parts split correctly.

Step 6

  • Gently remove the rubber keyboard from the device.

Gently remove the rubber keyboard from the device.

Step 7

              Wheelhead
  • Using a Phillips #0 screwdriver, remove the three 1.1 mm screws from the circuit board.

Using a Phillips #0 screwdriver, remove the three 1.1 mm screws from the circuit board.

Step 8

  • Lifting the circuit board, use a Phillips #1 screwdriver to remove the two 1.2mm screws from under the circuit board.

Lifting the circuit board, use a Phillips #1 screwdriver to remove the two 1.2mm screws from under the circuit board.

Step 9

  • Proceed to lift the excess device components until the rollerblade is visible.

Proceed to lift the excess device components until the rollerblade is visible.

Step 10

  • With the device components exposed, gently lift the wheelhead out of the label maker.

With the device components exposed, gently lift the wheelhead out of the label maker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 7 other contributors 


                    Matthew Jenkins

Member since: 01/27/2016

232 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       University of Alabama, Team 1-4, Sydow campbell Spring 2016                        

                                                  Member of University of Alabama, Team 1-4, Sydow campbell Spring 2016 



                    UA-SYDOW CAMPBELL-S16S1G4                     


                                            4 Members                     


                                            4 Guides authored

Zachary Parker - Nov 7, 2018

Reply

Group 9: Over all looks great. Pictures are great quality and hand placement in pictures. The circles and arrows should all be red. The only time the color changes is if there are different steps within a single picture.

aslan - May 31, 2020

Reply

thank you for the procedure, i mis one screen in the procedure how to detach display?