Dualsense Controller V2 Vibration Motor Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          1 - 2 hours

Sections

Middle Trim
5 steps
L1 and R1 Buttons
2 steps
Rear Case
4 steps
Battery
3 steps
Motherboard Removal
11 steps
Motherboard Desoldering
1 step
Vibration Motors
4 steps

Flags

BackDualSense Controller v2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Note: This guide is for current DualSense controllers with FCC IDs that end with A. Check the back of your controller to verify your model. If yours ends in a 1, it is an early model and there will be internal differences. Follow these guides for the earlier version.

What you need

Step 1

              Unclip the right end of the middle trim

Disconnect and power down your controller before you begin.
Insert an opening pick underneath the middle trim at the bottom-right corner of the controller to release the clips securing it to the case.

Disconnect and power down your controller before you begin.

Insert an opening pick underneath the middle trim at the bottom-right corner of the controller to release the clips securing it to the case.

1024

Step 2

              Unclip the lower-right edge of the middle trim

Slide the opening pick along the lower-right edge of the middle trim to release the clips securing it to the case.

Slide the opening pick along the lower-right edge of the middle trim to release the clips securing it to the case.

Step 3

              Unclip the left end of the middle trim

Insert an opening pick underneath the middle trim at the bottom-left corner of the controller to release the clips securing it to the case.

Insert an opening pick underneath the middle trim at the bottom-left corner of the controller to release the clips securing it to the case.

Step 4

              Unclip the lower-left edge of the middle trim

Slide the opening pick along the lower-left edge of the middle trim to release the clips securing it to the case.

Slide the opening pick along the lower-left edge of the middle trim to release the clips securing it to the case.

Step 5

              Remove the middle trim

Use your fingers to lift up the bottom edge of the middle trim to release the remaining clips.
Lift the middle trim over the joysticks to remove it.
During reassembly, position the middle trim into place and press along all edges to engage the clips securing it to the controller.

Use your fingers to lift up the bottom edge of the middle trim to release the remaining clips.

Lift the middle trim over the joysticks to remove it.

During reassembly, position the middle trim into place and press along all edges to engage the clips securing it to the controller.

Step 6

              Remove the L1 button

Insert the flat end of your spudger into the gap above the L1 button.
Cover the button with your thumb to prevent it from ejecting across the room.
Pry the spudger upward to remove the L1 button.

Insert the flat end of your spudger into the gap above the L1 button.

Cover the button with your thumb to prevent it from ejecting across the room.

Pry the spudger upward to remove the L1 button.

Step 7

              Remove the R1 button

Insert the flat end of your spudger into the gap above the R1 button.
Cover the button with your thumb to prevent it from ejecting across the room.
Pry the spudger upward to remove the R1 button.

Insert the flat end of your spudger into the gap above the R1 button.

Pry the spudger upward to remove the R1 button.

Step 8

              Remove the case screws

Use a Phillips screwdriver to remove the two 6.5 mm screws securing the bottom corners of the lower case.

Use a Phillips screwdriver to remove the two 6.5 mm screws securing the bottom corners of the lower case.

Step 9

Use a Phillips screwdriver to remove the two 6.5 mm screws behind the L1 and R1 buttons.

Use a Phillips screwdriver to remove the two 6.5 mm screws behind the L1 and R1 buttons.

Step 10

              Unclip the rear case

Use the pointed edge of a spudger to unclip the two clips on either side of the headset jack.

Use the pointed edge of a spudger to unclip the two clips on either side of the headset jack.

Step 11

              Remove the rear case

Use your hands to carefully pull the rear case off of the controller.
During reassembly, make sure the red and black vibration motor wires are not pinched between the front and rear case.

Use your hands to carefully pull the rear case off of the controller.

During reassembly, make sure the red and black vibration motor wires are not pinched between the front and rear case.

Step 12

              Reposition the battery

Lift the battery out of its bracket and reposition it to the right for better access to the battery connector.
Don’t strain the battery cables.

Lift the battery out of its bracket and reposition it to the right for better access to the battery connector.

Don’t strain the battery cables.

Step 13

              Disconnect the battery

Use a pair of tweezers or your fingers to disconnect the battery from the motherboard.
Don’t pull on the wires to disconnect the battery.

Use a pair of tweezers or your fingers to disconnect the battery from the motherboard.

Don’t pull on the wires to disconnect the battery.

Step 14

              Remove the battery

Remove the battery.

Remove the battery.

Step 15

              Remove the lower microphone

Use the pointed end of your spudger to remove the lower microphone from its bracket next to the battery.
During reassembly, make sure the end of the microphone’s ribbon cable is slotted into the bracket.

Use the pointed end of your spudger to remove the lower microphone from its bracket next to the battery.

During reassembly, make sure the end of the microphone’s ribbon cable is slotted into the bracket.

Step 16

Grab the lower microphone ribbon cable pull tab with your fingers or a pair of tweezers and disconnect it from the motherboard.

Grab the lower microphone ribbon cable pull tab with your fingers or a pair of tweezers and disconnect it from the motherboard.

Step 17

              Remove the battery bracket

Use a Phillips screwdriver to remove the 6.5 mm screw securing the battery bracket.

Use a Phillips screwdriver to remove the 6.5 mm screw securing the battery bracket.

Step 18

Lift the battery bracket off of the motherboard.

Lift the battery bracket off of the motherboard.

Step 19

              Disconnect the right trigger assembly

Grip the right trigger assembly cable with a pair of tweezers or your fingers and disconnect it from the motherboard.
Use the pull tab to disconnect the cable. Don’t pull on the cable itself.
Don’t completely remove the ribbon cable yet.

Grip the right trigger assembly cable with a pair of tweezers or your fingers and disconnect it from the motherboard.

Use the pull tab to disconnect the cable. Don’t pull on the cable itself.

Don’t completely remove the ribbon cable yet.

Step 20

Grip the right trigger assembly cable with a pair of tweezers or your fingers, and disconnect it from the trigger assembly.
Use the pull tab to disconnect the cable. Don’t pull on the cable itself.
Remove the ribbon cable.

Grip the right trigger assembly cable with a pair of tweezers or your fingers, and disconnect it from the trigger assembly.

Remove the ribbon cable.

Step 21

              Disconnect the left trigger assembly

Grip the left trigger assembly cable with a pair of tweezers or your fingers to disconnect it from the motherboard.
Use the pull tab to disconnect the cable. Don’t pull on the cable itself.
Don’t completely remove the ribbon cable yet.

Grip the left trigger assembly cable with a pair of tweezers or your fingers to disconnect it from the motherboard.

Step 22

Grip the left trigger assembly cable with a pair of tweezers or your fingers to disconnect it from the trigger assembly.
Use the pull tab to disconnect the cable. Don’t pull on the cable itself.
Remove the ribbon cable.

Grip the left trigger assembly cable with a pair of tweezers or your fingers to disconnect it from the trigger assembly.

Step 23

              Disconnect the upper microphone

Use a pair of tweezers or your fingers to disconnect the upper microphone from the motherboard.
Use the pull tab to disconnect the cable. Don’t pull on the cable itself.

Use a pair of tweezers or your fingers to disconnect the upper microphone from the motherboard.

Step 24

              Disconnect the touchpad

Use a pair of tweezers or your fingers to disconnect the touchpad cable from the motherboard.
Use the pull tab to disconnect the cable. Don’t pull on the cable itself.

Use a pair of tweezers or your fingers to disconnect the touchpad cable from the motherboard.

Step 25

              Lift out the motherboard

Carefully guide the joysticks through the front case and lift the motherboard out.
Don’t strain the four soldered wires tethering the motherboard to the vibration motors.

Carefully guide the joysticks through the front case and lift the motherboard out.

Don’t strain the four soldered wires tethering the motherboard to the vibration motors.

Step 26

              Desolder the vibration motor wires

Flip the motherboard and midframe over to access the red and black vibration motor wires.
Use a soldering iron to disconnect the vibration motor wires from the motherboard.
During reassembly, refer to this photo to ensure the wires are soldered back to their correct positions.

Flip the motherboard and midframe over to access the red and black vibration motor wires.

Use a soldering iron to disconnect the vibration motor wires from the motherboard.

During reassembly, refer to this photo to ensure the wires are soldered back to their correct positions.

Step 27

              Free the vibration motor wires

Use your spudger to slide the left vibration motor wires out of the midframe.

Use your spudger to slide the left vibration motor wires out of the midframe.

Step 28

Use your spudger to slide the right vibration motor wires out of the midframe.

Use your spudger to slide the right vibration motor wires out of the midframe.

Step 29

              Remove the left-hand vibration motor

Hold the midframe up to make sure the vibration motor isn’t resting on your work surface.
Press the flat end of your spudger into the midframe opening against the left-hand vibration motor.
Push to release the adhesive securing the vibration motor to the midframe.
If the adhesive is too strong, apply heat or 90% isopropyl alcohol to the back of the midframe to soften it.
During reassembly, apply some pre-cut adhesive to the new vibration motor to bond it to the midframe.

Hold the midframe up to make sure the vibration motor isn’t resting on your work surface.

Press the flat end of your spudger into the midframe opening against the left-hand vibration motor.

Push to release the adhesive securing the vibration motor to the midframe.

If the adhesive is too strong, apply heat or 90% isopropyl alcohol to the back of the midframe to soften it.

During reassembly, apply some pre-cut adhesive to the new vibration motor to bond it to the midframe.

Step 30

              Remove the right-hand vibration motor

Hold the midframe up to make sure the vibration motor isn’t resting on your work surface.
Press the flat end of your spudger into the midframe opening against the right-hand vibration motor.
Push to release the adhesive securing the vibration motor to the midframe.
If the adhesive is too strong, apply heat or 90% isopropyl alcohol to the back of the midframe to soften it.
During reassembly, apply some pre-cut adhesive to the new vibration motor to bond it to the midframe.

Press the flat end of your spudger into the midframe opening against the right-hand vibration motor.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                    Sam Omiotek

Member since: 02/25/2019

55,294 Reputation

                                      288 Guides authored                  



                       Badges:
                       35







                                                        +32 more badges

Team

                       Guide Team                        

                                                  Member of Guide Team 



                    Community                     


                                            10 Members                     


                                            9,216 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team