Difficulty
Moderate
Steps
10
Time Required
30 minutes
Sections
2
- Battery
- 7 steps
- Screen Assembly
- 3 steps
Flags
1
Missed a Step
Oops! This guide is currently missing some important steps.
BackMotorola Droid MAXX 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Insert a small pointed object into the hole on the sim card tray to eject the tray from the phone.
Insert a small pointed object into the hole on the sim card tray to eject the tray from the phone.
1024
Step 2
- Pull the sim card tray up out of the phone
Pull the sim card tray up out of the phone
Step 3
- Wedge your thumb into the indent located on the bottom left corner of the back cover and pull up to remove the back cover.
Wedge your thumb into the indent located on the bottom left corner of the back cover and pull up to remove the back cover.
Step 4
- Remove the seventeen 3.2mm Torx T4 screws from the mid-frame.
- These may be T3 screws. If you are having trouble unscrewing these, stop and try a T3 bit.
Remove the seventeen 3.2mm Torx T4 screws from the mid-frame.
These may be T3 screws. If you are having trouble unscrewing these, stop and try a T3 bit.
Step 5
- Pull the mid-frame off of the phone.
- Keep track of the on/off and volume buttons when you take the phone apart because they are likely to fall out when the halves are separated.
Pull the mid-frame off of the phone.
Keep track of the on/off and volume buttons when you take the phone apart because they are likely to fall out when the halves are separated.
Step 6
- Remove the static tape covering the two connectors.
- Use a spudger to disconnect the battery cables from the motherboard.
- If battery has adhesive, use heat gun for one to two minutes to loosen it. Be careful of the points outlined in red when prying it up. Use guitar picks or a spudger to gently lift the battery and separate the adhesive.
Remove the static tape covering the two connectors.
Use a spudger to disconnect the battery cables from the motherboard.
If battery has adhesive, use heat gun for one to two minutes to loosen it. Be careful of the points outlined in red when prying it up. Use guitar picks or a spudger to gently lift the battery and separate the adhesive.
Step 7
- Remove the disconnected battery from the phone.
Remove the disconnected battery from the phone.
Step 8
Screen Assembly
- We will be removing these 3 ribbon cables.
- Using an opening pick, lift the grey tab on the rear camera’s ZIF connector. Remove the ribbon cable and the camera.
- Use tweezers to lift up on the grey latch on the ZIF connector.
- Remove the ribbon cable from the ZIF connector.
We will be removing these 3 ribbon cables.
Using an opening pick, lift the grey tab on the rear camera’s ZIF connector. Remove the ribbon cable and the camera.
Use tweezers to lift up on the grey latch on the ZIF connector.
Remove the ribbon cable from the ZIF connector.
Step 9
- Use a pair of tweezers to lift up the black latch on the ZIF connector.
- Pull the ribbon cable out of the ZIF connector.
Use a pair of tweezers to lift up the black latch on the ZIF connector.
Pull the ribbon cable out of the ZIF connector.
Step 10
- Using a metal spudger, work your way around the perimeter of the main board and screen.
- There is a lot of adhesive between the two pieces, so be careful to try to remove the adhesive slowly in order to not break anything.
Using a metal spudger, work your way around the perimeter of the main board and screen.
There is a lot of adhesive between the two pieces, so be careful to try to remove the adhesive slowly in order to not break anything.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Burke Seggerman
Member since: 03/18/2018
704 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
Baylor, Team S3-G4, Williams Spring 2018
Member of Baylor, Team S3-G4, Williams Spring 2018
BU-WILLIAMS-S18S3G4
3 Members
6 Guides authored
