Difficulty

Moderate

Steps

8

Time Required

                          40 - 45 minutes

Sections

3

  • Battery
  • 1 step
  • Casing
  • 3 steps
  • Camera
  • 4 steps

Flags

0

  • BackDROCON Ninja

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Make sure the drone is powered off before beginning the battery replacement.
  • To turn the drone off, press and hold the black button on the top of the drone until all lights are off.
  • Firmly grasp the battery tab between your thumb and index finger.
  • Pull the battery away from the drone’s body

Make sure the drone is powered off before beginning the battery replacement.

To turn the drone off, press and hold the black button on the top of the drone until all lights are off.

Firmly grasp the battery tab between your thumb and index finger.

Pull the battery away from the drone’s body

1024

Step 2

              Casing
  • Using a Phillips #00 Screwdriver remove the eight 4mm screws on the bottom of the drone.

Using a Phillips #00 Screwdriver remove the eight 4mm screws on the bottom of the drone.

Step 3

  • Gently pull white casing away from the black bottom casing

Gently pull white casing away from the black bottom casing

Step 4

  • Insert the opening tool under one of the black plastic connector slots that connects the circuit-board to the casing.
  • Gently pull the opening tool toward you to disconnect the circuit-board from the plastic casing.

Insert the opening tool under one of the black plastic connector slots that connects the circuit-board to the casing.

Gently pull the opening tool toward you to disconnect the circuit-board from the plastic casing.

Step 5

              Camera
  • Use a Phillips #00 screwdriver to remove the 5mm screws connecting the front two motor arms to the drone’s body.
  • Use your fingers to gently pull the white plastic discs out of the motor arms.

Use a Phillips #00 screwdriver to remove the 5mm screws connecting the front two motor arms to the drone’s body.

Use your fingers to gently pull the white plastic discs out of the motor arms.

Step 6

  • Grasp the motor arm and pull up and away from the drone’s body.
  • Repeat this step for the other front motor arm.

Grasp the motor arm and pull up and away from the drone’s body.

Repeat this step for the other front motor arm.

Step 7

  • Using the Phillips #00 screwdriver, remove the two 3mm screws on the control board.

Using the Phillips #00 screwdriver, remove the two 3mm screws on the control board.

Step 8

  • Using the opening tool flip up the black plastic clamp that holds the camera wire to the circuit board.
  • Gently pull the camera out from the control board.

Using the opening tool flip up the black plastic clamp that holds the camera wire to the circuit board.

Gently pull the camera out from the control board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Destinee Easterly

Member since: 01/26/2020

262 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Embry-Riddle Aeronautical University, Team S3-G5, Watkins Spring 2020                        

                                                  Member of Embry-Riddle Aeronautical University, Team S3-G5, Watkins Spring 2020 



                    ERAU-WATKINS-S20S3G5                     


                                            4 Members                     


                                            5 Guides authored