Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
3
- Front Panel Assembly
- 4 steps
- Motherboard
- 6 steps
- Button Panel
- 1 step
Flags
0
BackDKnight MagicBox II
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Panel Assembly
- Using Blue Plastic opening tool pry the top rubber cover, then using the same tool remove the bottom panel
Using Blue Plastic opening tool pry the top rubber cover, then using the same tool remove the bottom panel
1024
Step 2
- There are four prongs on the grill in the corners, closest to the power button switch. Use the plastic opening tool to release all four prongs from the panel, and then slide the plastic opening tool along the edge of the grill to allow it to easily slide off.
There are four prongs on the grill in the corners, closest to the power button switch. Use the plastic opening tool to release all four prongs from the panel, and then slide the plastic opening tool along the edge of the grill to allow it to easily slide off.
Step 3
- On the back panel (Opposite to the side containing the two speakers), Use the Philips head PH1 to remove all 7 screws (Screws: Head PH1 , Length 7cm).
On the back panel (Opposite to the side containing the two speakers), Use the Philips head PH1 to remove all 7 screws (Screws: Head PH1 , Length 7cm).
Step 4
- Pull apart the two faces to separate the back panel from the front face plate.
Pull apart the two faces to separate the back panel from the front face plate.
Step 5
Motherboard
- Remove the single screw holding the motherboard to the front panel (Screw : Head PH1, Size .5 cm)
Remove the single screw holding the motherboard to the front panel (Screw : Head PH1, Size .5 cm)
Step 6
- Using your fingers gently pry the motherboard loose from the black insulant adhesive
Using your fingers gently pry the motherboard loose from the black insulant adhesive
Step 7
- Disconnect the Button Panel plug (Largest of the Plugs, it can be traced back to the button panel easily)
Disconnect the Button Panel plug (Largest of the Plugs, it can be traced back to the button panel easily)
Step 8
- Use the tweezers to push down on the safety prongs on the plastic switch. Then Disconnect the Power Wire plug by hand (Red medium),
Use the tweezers to push down on the safety prongs on the plastic switch. Then Disconnect the Power Wire plug by hand (Red medium),
Step 9
- Use the tweezers to push down on the two safety prongs on the plastic switch. Then Disconnect the two Speaker plug connections by hand (Two Smaller Plugs)
Use the tweezers to push down on the two safety prongs on the plastic switch. Then Disconnect the two Speaker plug connections by hand (Two Smaller Plugs)
Step 10
- The Motherboard is now free from the speaker assembly
The Motherboard is now free from the speaker assembly
Step 11
Button Panel
- Remove the three screws holding the button board in place (Screw Head PH1, Size 0.5 cm)
- You should now be able to remove the button panel from the device.
Remove the three screws holding the button board in place (Screw Head PH1, Size 0.5 cm)
You should now be able to remove the button panel from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Anthony
Member since: 02/04/2016
695 Reputation
3 Guides authored
Badges:
14
+11 more badges
Team
USF Tampa, Team 17-1, Blackwell Winter 2016
Member of USF Tampa, Team 17-1, Blackwell Winter 2016
USFT-BLACKWELL-W16S17G1
4 Members
3 Guides authored
