Difficulty

Difficult

Steps

10

Time Required

                          20 - 45 minutes

Sections

4

  • Propellers
  • 2 steps
  • Battery
  • 1 step
  • Lid
  • 2 steps
  • Camera
  • 5 steps

Flags

1

Missing Details

Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.

  • BackDJI Spark

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Propellers
  • Push down on the propeller that is being replaced.

Push down on the propeller that is being replaced.

1024

Step 2

  • Twist the propeller until it feels loose.
  • Pull on it until it comes off.

Twist the propeller until it feels loose.

Pull on it until it comes off.

Step 3

              Battery
  • Flip the drone over.
  • Grip the left and right sides of the battery.
  • Slide firmly forward until it pops out.

Flip the drone over.

Grip the left and right sides of the battery.

Slide firmly forward until it pops out.

Step 4

              Lid
  • Flip the drone over.
  • Remove the four 1.5mm Hex screws.
  • Remove the two 1.5mm Hex screws near the camera head.
  • You may need to remove plastic nubs from the hex screws using a spudger first.

Remove the four 1.5mm Hex screws.

Remove the two 1.5mm Hex screws near the camera head.

You may need to remove plastic nubs from the hex screws using a spudger first.

Step 5

  • Hold the drone so the lid is facing up.
  • Insert the plastic opening tool into the side of the drone.
  • Slide the tool around the perimeter until you can lift the top off.

Hold the drone so the lid is facing up.

Insert the plastic opening tool into the side of the drone.

Slide the tool around the perimeter until you can lift the top off.

Step 6

              Camera
  • Disconnect two gold antenna next to the internal GPS while removing the motherboard.

Disconnect two gold antenna next to the internal GPS while removing the motherboard.

Step 7

  • Remove all the Phillips #0 screws attaching the motherboard to the drone.
  • It is the piece with both the fan and GPS module on it.

Remove all the Phillips #0 screws attaching the motherboard to the drone.

It is the piece with both the fan and GPS module on it.

Step 8

  • Remove the 3.0 mm Phillips #000 screw.

Remove the 3.0 mm Phillips #000 screw.

Step 9

  • Remove the two Phillips #0 screws on the right and left sides.
  • Once removed, pull the front facing sensor out.

Remove the two Phillips #0 screws on the right and left sides.

Once removed, pull the front facing sensor out.

Step 10

  • Gently remove the gimbal along with the camera from the top of the device.

Gently remove the gimbal along with the camera from the top of the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Amelia Hagberg

Member since: 10/21/2019

403 Reputation

                                      3 Guides authored                  



                       Badges:
                       7





                                                        +4 more badges

Team

                       UMass Dartmouth, Team S1-G7, Botvin Fall 2019                        

                                                  Member of UMass Dartmouth, Team S1-G7, Botvin Fall 2019 



                    UMASSD-BOTVIN-F19S1G7                     


                                            3 Members                     


                                            7 Guides authored

Basil Yokarinis - Apr 19, 2020

Reply

Good start, but missing many steps and details.

sebasnavarro1116 - Jan 15, 2022

Reply

I am now going to try and fix my drone. thank you so much