Dji Phantom 4 Advanced Remote Controller Power Button Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          10 - 25 minutes            

Sections

3

• Back Panel
• 5 steps
• Motherboard
• 3 steps
• Power Button
• 3 steps

Flags

2

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackDJI Phantom 4 Advanced Remote Controller

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Back Panel               

• Remove the four screws with a Torx T8 screwdriver to access the back con board.

Remove the four screws with a Torx T8 screwdriver to access the back con board.

1024

Step 2

• Remove three screws using a Phillips #00 screwdriver.

Remove three screws using a Phillips #00 screwdriver.

Step 3

• With tweezers, gently remove the large con board tab.
• Use your hands to remove the two small clips. Pull out from the socket, in a horizontal direction.

With tweezers, gently remove the large con board tab.

Use your hands to remove the two small clips. Pull out from the socket, in a horizontal direction.

Step 4

• Peel off the rubber grips to access the screw holes.
• Make sure to save your grips and do not to get them stuck to anything, you are going to want to save the adhesive.
• Remove the back board and set it aside.

Peel off the rubber grips to access the screw holes.

Make sure to save your grips and do not to get them stuck to anything, you are going to want to save the adhesive.

Remove the back board and set it aside.

Step 5

• Pull apart the back plastic panel.
• Recommended tool for this would be the metal spudger, but not required.
• Once the back panel is off, you will have access to the motherboard.

Pull apart the back plastic panel.

Recommended tool for this would be the metal spudger, but not required.

Once the back panel is off, you will have access to the motherboard.

Step 6

              Motherboard               

• Disconnect ribbon tabs 1,2,5,8G, and 3.
• Remove ribbon tab by pulling gently along motherboard. Do not pull straight out.
• Then remove the plugs

Disconnect ribbon tabs 1,2,5,8G, and 3.

Remove ribbon tab by pulling gently along motherboard. Do not pull straight out.

Then remove the plugs

Step 7

• With the Phillips #00 screwdriver, remove the two Phillips screws.

With the Phillips #00 screwdriver, remove the two Phillips screws.

Step 8

• Double check to make sure all tabs, plugs and screws are removed or disconnected.
• Gently lift motherboard out of the case.

Double check to make sure all tabs, plugs and screws are removed or disconnected.

Gently lift motherboard out of the case.

Step 9

              Power Button               

• Carefully remove the plastic. This will help you gain access to the power button panel.

Carefully remove the plastic. This will help you gain access to the power button panel.

Step 10

• With a Phillips #00 screwdriver, remove the two screws on the power button panel.

With a Phillips #00 screwdriver, remove the two screws on the power button panel.

Step 11

• Gently pull the power button out from the panel. Replace it with a new one.

Gently pull the power button out from the panel. Replace it with a new one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 4 other contributors 

                    Angel Cortez                     

Member since: 10/02/2018

234 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges                           

Team

                       Linn Benton Community College, Team S1-G4, Johnson Fall 2018                        

                                                  Member of Linn Benton Community College, Team S1-G4, Johnson Fall 2018 



                    LBCC-JOHNSON-F18S1G4                     


                                            3 Members                     


                                            12 Guides authored