Difficulty

Moderate

Steps

9

Time Required

                          15 minutes

Sections

3

  • Battery
  • 1 step
  • Upper Shell
  • 6 steps
  • WiFi Board
  • 2 steps

Flags

0

  • BackDJI Mavic Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Grab both sides of the battery.
  • Pinch the releasing buttons on both sides of the battery.
  • Lift the battery up and out.

Grab both sides of the battery.

Pinch the releasing buttons on both sides of the battery.

Lift the battery up and out.

1024

Step 2

              Upper Shell
  • Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.

Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.

Step 3

  • Flip the drone over so that the gimbal is facing up.
  • Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
  • Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Flip the drone over so that the gimbal is facing up.

Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Step 4

  • Remove the two small panel pieces near the gimbal case with the tweezers.

Remove the two small panel pieces near the gimbal case with the tweezers.

Step 5

  • Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.

Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.

Step 6

  • Flip the drone back over so the upper shell is facing up.
  • Pry off the upper shell with a nylon spudger.
  • Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.

Flip the drone back over so the upper shell is facing up.

Pry off the upper shell with a nylon spudger.

Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.

Step 7

  • Remove the white connector at the back of the flight controller board by gently pulling at the base.

Remove the white connector at the back of the flight controller board by gently pulling at the base.

Step 8

              WiFi Board
  • Remove the lone 4mm Phillips #00 screw holding the WiFi board in place by turning the screwdriver counterclockwise.

Remove the lone 4mm Phillips #00 screw holding the WiFi board in place by turning the screwdriver counterclockwise.

Step 9

  • Remove the two gold coaxial connectors by pulling gently at the base with tweezers.

Remove the two gold coaxial connectors by pulling gently at the base with tweezers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Mondona Behroozian

Member since: 10/08/2018

1,410 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team S17-G3, White Fall 2018                        

                                                  Member of Cal Poly, Team S17-G3, White Fall 2018 



                    CPSU-WHITE-F18S17G3                     


                                            4 Members                     


                                            14 Guides authored

Quentin V - Sep 29, 2020

Reply

Is it possible to remove the wifi card completely and fly the drone without it ?

Chris Stoll - Oct 25, 2020

Reply

Are there any connectivity issues, like new passwords etc?

Mike Belanger - Jul 24, 2022

Reply

Mine was removed by the former owner and the coaxial connectors were removed at the same time. I bought a new module that has the coaxial wires and one ribbon cable and now I have to see about removing either the bottom of the drone or one of the boards to gain access to where these connectors go to. Is there another video as to how to do that? Several of the hex screws are stripped to the point where my 5mm hex screwdriver don’t remove them. Is there a fix for that (stripped screws)?