Difficulty

Moderate

Steps

7

Time Required

                          8 minutes

Sections

2

  • Battery
  • 1 step
  • Upper Shell
  • 6 steps

Flags

0

  • BackDJI Mavic Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Grab both sides of the battery.
  • Pinch the releasing buttons on both sides of the battery.
  • Lift the battery up and out.

Grab both sides of the battery.

Pinch the releasing buttons on both sides of the battery.

Lift the battery up and out.

1024

Step 2

              Upper Shell
  • Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.

Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.

Step 3

  • Flip the drone over so that the gimbal is facing up.
  • Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
  • Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Flip the drone over so that the gimbal is facing up.

Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Step 4

  • Remove the two small panel pieces near the gimbal case with the tweezers.

Remove the two small panel pieces near the gimbal case with the tweezers.

Step 5

  • Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.

Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.

Step 6

  • Flip the drone back over so the upper shell is facing up.
  • Pry off the upper shell with a nylon spudger.
  • Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.

Flip the drone back over so the upper shell is facing up.

Pry off the upper shell with a nylon spudger.

Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.

Step 7

  • Remove the white connector at the back of the flight controller board by gently pulling at the base.

Remove the white connector at the back of the flight controller board by gently pulling at the base.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 7 other contributors 


                    Mondona Behroozian

Member since: 10/08/2018

1,410 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team S17-G3, White Fall 2018                        

                                                  Member of Cal Poly, Team S17-G3, White Fall 2018 



                    CPSU-WHITE-F18S17G3                     


                                            4 Members                     


                                            14 Guides authored

Lazaro Hernandez - Jun 5, 2019

Reply

Well done, good instructions - are the two screws under the tabs shorter than the others from the shell?

shaun.cunningham - Jan 14, 2021

Reply

Awesome descriptions were perfect except for saying there is 4 acres to be removed under the tabs behind the gimbal. Theirs only 2