Difficulty
Easy
Steps
10
Time Required
15 minutes
Sections
3
- Battery
- 1 step
- Upper Shell
- 6 steps
- GPS Module
- 3 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackDJI Mavic Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Grab both sides of the battery.
- Pinch the releasing buttons on both sides of the battery.
- Lift the battery up and out.
Grab both sides of the battery.
Pinch the releasing buttons on both sides of the battery.
Lift the battery up and out.
1024
Step 2
Upper Shell
- Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.
Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.
Step 3
- Flip the drone over so that the gimbal is facing up.
- Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
- Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
Flip the drone over so that the gimbal is facing up.
Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
Step 4
- Remove the two small panel pieces near the gimbal case with the tweezers.
Remove the two small panel pieces near the gimbal case with the tweezers.
Step 5
- Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.
Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.
Step 6
- Flip the drone back over so the upper shell is facing up.
- Pry off the upper shell with a nylon spudger.
- Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.
Flip the drone back over so the upper shell is facing up.
Pry off the upper shell with a nylon spudger.
Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.
Step 7
- Remove the white connector at the back of the flight controller board by gently pulling at the base.
Remove the white connector at the back of the flight controller board by gently pulling at the base.
Step 8
GPS Module
- Flip the upper shell over so the metallic plate is facing up.
- Remove the two 5mm JIS #00 screws from the metallic plate by turning the screwdriver counterclockwise.
- If the JIS #00 screwdriver is too small, you may need to use a JIS #0 screwdriver.
Flip the upper shell over so the metallic plate is facing up.
Remove the two 5mm JIS #00 screws from the metallic plate by turning the screwdriver counterclockwise.
If the JIS #00 screwdriver is too small, you may need to use a JIS #0 screwdriver.
Step 9
- Pry the metallic plate up from the upper shell by using a nylon spudger.
- Remove the metallic plate from the upper shell by lifting the plate up and out.
- You may hear a popping sound when prying the metallic plate, but no damage will occur.
Pry the metallic plate up from the upper shell by using a nylon spudger.
Remove the metallic plate from the upper shell by lifting the plate up and out.
You may hear a popping sound when prying the metallic plate, but no damage will occur.
Step 10
- Use tweezers to remove the GPS Module from the upper shell.
Use tweezers to remove the GPS Module from the upper shell.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
8 other people completed this guide.
Author
with 4 other contributors
Kyle Kelser
Member since: 10/08/2018
551 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
Cal Poly, Team S17-G3, White Fall 2018
Member of Cal Poly, Team S17-G3, White Fall 2018
CPSU-WHITE-F18S17G3
4 Members
14 Guides authored
