Dji Mavic Pro Front Vision Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Battery
1 step
Upper Shell
6 steps
Gimbal/Camera
10 steps
Front Vision
2 steps

Flags

BackDJI Mavic Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Grab both sides of the battery.
Pinch the releasing buttons on both sides of the battery.
Lift the battery up and out.

Grab both sides of the battery.

Pinch the releasing buttons on both sides of the battery.

Lift the battery up and out.

1024

Step 2

              Upper Shell

Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.

Remove the six 5mm 1.5 Hex screws by turning the screwdriver counterclockwise.

Step 3

Flip the drone over so that the gimbal is facing up.
Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.
Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Flip the drone over so that the gimbal is facing up.

Remove the two 4mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Remove the two 5mm 1.5 Hex screws near the gimbal case by turning the screwdriver counterclockwise.

Step 4

Remove the two small panel pieces near the gimbal case with the tweezers.

Remove the two small panel pieces near the gimbal case with the tweezers.

Step 5

Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.

Remove the six 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.

Step 6

Flip the drone back over so the upper shell is facing up.
Pry off the upper shell with a nylon spudger.
Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.

Flip the drone back over so the upper shell is facing up.

Pry off the upper shell with a nylon spudger.

Be careful when prying with the spudger because you could damage the upper shell’s plastic tabs.

Step 7

Remove the white connector at the back of the flight controller board by gently pulling at the base.

Remove the white connector at the back of the flight controller board by gently pulling at the base.

Step 8

              Gimbal/Camera

Remove the one 5mm JIS #0 screw from the small micro controller board at the front of the DJI Mavic Pro by turning counterclockwise.

Remove the one 5mm JIS #0 screw from the small micro controller board at the front of the DJI Mavic Pro by turning counterclockwise.

Step 9

Pull the cord and micro controller board away from the front of the DJI Mavic Pro using tweezers.

Pull the cord and micro controller board away from the front of the DJI Mavic Pro using tweezers.

Step 10

Expose the two small ZIF connectors near the front of the board by removing the plastic coverings.
Then, remove the two ZIF connectors under the coverings using a nylon spudger.

Expose the two small ZIF connectors near the front of the board by removing the plastic coverings.

Then, remove the two ZIF connectors under the coverings using a nylon spudger.

Step 11

Remove two 6mm JIS #00 screws from the plastic board cover at the front of the DJI Mavic Pro.

Remove two 6mm JIS #00 screws from the plastic board cover at the front of the DJI Mavic Pro.

Step 12

Flip the DJI Mavic Pro over.
Gently press the latch for the Gimbal cover.
Pull the cover off.

Flip the DJI Mavic Pro over.

Gently press the latch for the Gimbal cover.

Pull the cover off.

Step 13

Flip the DJI Mavic Pro back over, with its top side facing up.
Remove the two ZIF connectors located behind the plastic covers by using a nylon spudger.

Flip the DJI Mavic Pro back over, with its top side facing up.

Remove the two ZIF connectors located behind the plastic covers by using a nylon spudger.

Step 14

Gently remove the power cable connector located to the left, behind the gimbal board, by pulling up on the white base.

Gently remove the power cable connector located to the left, behind the gimbal board, by pulling up on the white base.

Step 15

Scrape away the plastic adhesive covering the two 5mm JIS #000 screws connected to the gimbal board.
Remove the two 5mm JIS #000 screws from the gimbal board by turning the screwdriver counterclockwise.

Scrape away the plastic adhesive covering the two 5mm JIS #000 screws connected to the gimbal board.

Remove the two 5mm JIS #000 screws from the gimbal board by turning the screwdriver counterclockwise.

Step 16

Remove the two 7mm JIS #00 screws at the very front of the DJI Mavic Pro by turning the screwdriver counterclockwise.
Careful when removing these screws the camera or whatever remains of your camera assembly may drop

Remove the two 7mm JIS #00 screws at the very front of the DJI Mavic Pro by turning the screwdriver counterclockwise.

Careful when removing these screws the camera or whatever remains of your camera assembly may drop

Step 17

Flip the DJI Mavic Pro over, with the camera facing you.
Gently pull the gimbal/camera assembly up and out.

Flip the DJI Mavic Pro over, with the camera facing you.

Gently pull the gimbal/camera assembly up and out.

Step 18

              Front Vision

Remove the two 6mm JIS #0 screws by turning counterclockwise.

Remove the two 6mm JIS #0 screws by turning counterclockwise.

Step 19

Remove the front vision piece by pulling the piece up and away from the drone body.

Remove the front vision piece by pulling the piece up and away from the drone body.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 4 other contributors

                    Kyle Kelser

Member since: 10/08/2018

551 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team S17-G3, White Fall 2018                        

                                                  Member of Cal Poly, Team S17-G3, White Fall 2018 



                    CPSU-WHITE-F18S17G3                     


                                            4 Members                     


                                            14 Guides authored

Daniel Rubio Rocamora - Jun 12, 2020

What error codes did you get before having to replace this front cameras?

Introduction#

What you need#

Team#

Introduction

What you need

Team