Disassembling Olympus Stylus Tough 6020 Prerequisite Guide Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 25 minutes

Sections

Prerequisite Guide
9 steps

Flags

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

BackOlympus Stylus Tough 6020
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Slide and push the battery casing to open it.
Push the battery to eject it.

Slide and push the battery casing to open it.

Push the battery to eject it.

1024

Step 2

              Bottom Plating

Turn the camera so that you are facing the bottom of the camera.
Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws on the bottom of the camera.
Using a spudger, pry off the plating on the bottom of the camera.

Turn the camera so that you are facing the bottom of the camera.

Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws on the bottom of the camera.

Using a spudger, pry off the plating on the bottom of the camera.

Step 3

              Top Plating

Turn the camera so that you are facing the top of the camera.
Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws located on the top of the camera.
Using a spudger, pry off the plating on the top of the camera.

Turn the camera so that you are facing the top of the camera.

Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws located on the top of the camera.

Using a spudger, pry off the plating on the top of the camera.

Step 4

              Left Plating

Turn the camera so the LCD is facing upwards.
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws located on the left side of the device.

Turn the camera so the LCD is facing upwards.

Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws located on the left side of the device.

Step 5

              Black "Olympus" Face Plate

Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located next to the black “Olympus” face plate.
Using a T6 Torx screwdriver, unscrew the two 3.5mm screws located on the black “Olympus” face plate.
Using a spudger, gently pry off the black “Olympus” face plate.

Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located next to the black “Olympus” face plate.

Using a T6 Torx screwdriver, unscrew the two 3.5mm screws located on the black “Olympus” face plate.

Using a spudger, gently pry off the black “Olympus” face plate.

Step 6

              End Casing

Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws to the right of the cursor pad on the U-shaped frame.
Turn the device over so the front of the camera is facing you.
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws on the end casing.
Using a spudger, pry off the end casing.

Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws to the right of the cursor pad on the U-shaped frame.

Turn the device over so the front of the camera is facing you.

Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws on the end casing.

Using a spudger, pry off the end casing.

Step 7

              Blue Face Plate

Turn the camera so the blue face plate is visible.
Using a Phillips 00 screwdriver, unscrew the two 3mm screws on the blue plate.
Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located at the bottom of the camera straight down from the flash.
Using a spudger, gently pry off the blue face plate.

Turn the camera so the blue face plate is visible.

Using a Phillips 00 screwdriver, unscrew the two 3mm screws on the blue plate.

Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located at the bottom of the camera straight down from the flash.

Using a spudger, gently pry off the blue face plate.

Step 8

              Back Plate

Using a Phillips 00 screwdriver, unscrew the 9mm screws on the top of the camera to the right of the flash.

Using a Phillips 00 screwdriver, unscrew the 9mm screws on the top of the camera to the right of the flash.

Step 9

Using a Phillips 00 screwdriver, unscrew the wide 3.5mm screw located in the middle of the camera.
Using a Phillips 00 screwdriver, unscrew the 9mm screw located at the top left corner of the camera.
Using a spudger, separate the black plate from the camera.

Using a Phillips 00 screwdriver, unscrew the wide 3.5mm screw located in the middle of the camera.

Using a Phillips 00 screwdriver, unscrew the 9mm screw located at the top left corner of the camera.

Using a spudger, separate the black plate from the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors

                    Taylor Carabin

Member since: 04/15/2015

259 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Eastern Washington University, Team 2-6, Matresse Spring 2015                        

                                                  Member of Eastern Washington University, Team 2-6, Matresse Spring 2015 



                    EWU-MATRESSE-S15S2G6                     


                                            4 Members                     


                                            12 Guides authored

Inconsistent Images#

Introduction#

What you need#

Team#

Inconsistent Images

Introduction

What you need

Team