Difficulty
Moderate
Steps
10
Time Required
30 minutes - 1 hour
Sections
1
- Disassembling Nokia X2-00
- 10 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackNokia X2-00
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
I’m not professional, so my lighting and photo quality isn’t Perfect, i just don’t have money to invest
What you need
Step 1
Nokia X2-00 Background Info
- it’s a cheap low-end Music Phone
- mine got wet so i decided to clean it up and look inside!
it’s a cheap low-end Music Phone
mine got wet so i decided to clean it up and look inside!
1024
Step 2
Removing the Battery
- Flip it and pull the tab
- the metal part should jump right off
- after that remove the battery and sim card
Flip it and pull the tab
the metal part should jump right off
after that remove the battery and sim card
Step 3
Diging In!
- so i was kinda !#^&@@ off becouse there were no screws!
- so i tryed to remove the screen protection, and it worked!
- i did break it
- there were no screws
- just don’t do that unless you need
so i was kinda !#^&@@ off becouse there were no screws!
so i tryed to remove the screen protection, and it worked!
i did break it
there were no screws
just don’t do that unless you need
Step 4
Diging In! 2nd attemp!
- i tried to remove the side panels but that didn’t work so i tried on top and it did work (Jimmy worked fine)
- these clips kind of suck ….it takes lot of force to unclip these )
- after you unclip it you get that piece
i tried to remove the side panels but that didn’t work so i tried on top and it did work (Jimmy worked fine)
these clips kind of suck ….it takes lot of force to unclip these )
after you unclip it you get that piece
Step 5
Removing the midframe
- remove these 2 TR6 Screws (mine were a bit blue)
- open it up (clips on the bottom)
- i was on Beast-Mode on these annying clips that held like gorilla
remove these 2 TR6 Screws (mine were a bit blue)
open it up (clips on the bottom)
i was on Beast-Mode on these annying clips that held like gorilla
Step 6
Removing the display
- Remove the 4 TR6 Screws
- They are diffrent from the last ones !!! (this one on the right)
- remove the whole PCB and remove the clips from the display and it should pop off
Remove the 4 TR6 Screws
They are diffrent from the last ones !!! (this one on the right)
remove the whole PCB and remove the clips from the display and it should pop off
Step 7
The Display
- it’s TFT 2.2" 240x320 182 ppi Display
it’s TFT 2.2" 240x320 182 ppi Display
Step 8
The main PCB
- anything shiehielded …and non-replacable …i don’t like that one at all
- sorry guys i have forgott to make photo of the backside :(
anything shiehielded …and non-replacable …i don’t like that one at all
sorry guys i have forgott to make photo of the backside :(
Step 9
Extra - Mastery pieces & Test
- extra steps that you don’t need to do
- 2 of those fell of and i have NO idea where from (and i don’t even care)
- i cleaned it up and powered it up and it works (just make sure you don’t short anything)
extra steps that you don’t need to do
2 of those fell of and i have NO idea where from (and i don’t even care)
i cleaned it up and powered it up and it works (just make sure you don’t short anything)
Step 10
The END
- i don’t really like that one becouse it’s hard to open and easy to crack plastics
- but you can replace many things (not anything)
- i would like USB on doughterboard and less shielding
i don’t really like that one becouse it’s hard to open and easy to crack plastics
but you can replace many things (not anything)
i would like USB on doughterboard and less shielding
Cancel: I did not complete this guide.
8 other people completed this guide.
Author
with 3 other contributors
Mateusz
Member since: 10/20/2014
1,447 Reputation
2 Guides authored
Badges:
15
+12 more badges
Segmenttopten - Dec 12, 2016
Reply
Well done,come on
