Difficulty
Moderate
Steps
13
Time Required
30 minutes
Sections
2
- Stand
- 6 steps
- Monitor Enclosure
- 7 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackNEC MultiSync LCD1770NX
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Stand
- Place the monitor face down on a clean, flat surface.
Place the monitor face down on a clean, flat surface.
1024
Step 2
- Firmly remove the back panel of the stand by pulling it up and away from the monitor.
Firmly remove the back panel of the stand by pulling it up and away from the monitor.
Step 3
- Unscrew the two 6mm Phillips PH2 screws to detach the stand enclosure from the stand.
Unscrew the two 6mm Phillips PH2 screws to detach the stand enclosure from the stand.
Step 4
- Firmly grasp the stand enclosure with your hand and slide it to base of stand.
Firmly grasp the stand enclosure with your hand and slide it to base of stand.
Step 5
- Unscrew the two 14.5mm Phillips PH2 screws holding the stand to the monitor.
Unscrew the two 14.5mm Phillips PH2 screws holding the stand to the monitor.
Step 6
- Lift the the stand straight up to remove it.
Lift the the stand straight up to remove it.
Step 7
Monitor Enclosure
- Place the monitor screen face up.
- Pull the frame off by placing your fingers on the inside of the frame and pulling out and up, the frame should snap off.
- Continue your way around the screen.
Place the monitor screen face up.
Pull the frame off by placing your fingers on the inside of the frame and pulling out and up, the frame should snap off.
Continue your way around the screen.
Step 8
- Unscrew the two 7mm screws from the bottom of the button assembly.
- Do not pull the button assembly out too quickly or with too much force! Damage to the wires can occur.
- Pull the button assembly out a few inches and unplug the colored cables.
Unscrew the two 7mm screws from the bottom of the button assembly.
Do not pull the button assembly out too quickly or with too much force! Damage to the wires can occur.
Pull the button assembly out a few inches and unplug the colored cables.
Step 9
- Unscrew the gold colored 7mm Phillips PH000 screw holding the button assembly to the monitor.
- Remove the button assembly from the monitor.
Unscrew the gold colored 7mm Phillips PH000 screw holding the button assembly to the monitor.
Remove the button assembly from the monitor.
Step 10
- With the monitor face-down, unscrew the 5 7mm Phillips PH2 screws around the outside of the enclosure.
With the monitor face-down, unscrew the 5 7mm Phillips PH2 screws around the outside of the enclosure.
Step 11
- Unscrew the 2 14.5mm Phillips PH2 screws located on the raised center of the enclosure.
- Carefully pull the enclosure off the monitor.
Unscrew the 2 14.5mm Phillips PH2 screws located on the raised center of the enclosure.
Carefully pull the enclosure off the monitor.
Step 12
- Unscrew the 10 5mm Philips PH2 screws holding the metal casing to the monitor.
Unscrew the 10 5mm Philips PH2 screws holding the metal casing to the monitor.
Step 13
- Pull the the metal casing off of the monitor to reveal the motherboards.
Pull the the metal casing off of the monitor to reveal the motherboards.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 7 other contributors
John Patterson
Member since: 10/19/2013
253 Reputation
2 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 11-36, Amido Fall 2013
Member of Cal Poly, Team 11-36, Amido Fall 2013
CPSU-AMIDO-F13S11G36
5 Members
7 Guides authored
Richard Morgan - Dec 21, 2021
Reply
very helpful
Thank you
