Disassembling Insignia Flex 8 Circuit Board Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Circuit Board
10 steps

Flags

BackInsignia Flex 8 NS-14T002
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Circuit Board

Turn off the power to your tablet to avoid injury.
Position the tablet so that the screen is face down and the power button is located in the upper left hand corner.
Hold down the power button for five seconds until the tablet powers down.

Turn off the power to your tablet to avoid injury.

Position the tablet so that the screen is face down and the power button is located in the upper left hand corner.

Hold down the power button for five seconds until the tablet powers down.

1024

Step 2

Remove the back casing from the screen by sliding a credit card or a similarly thin but firm object in between the casing and the screen.
You may need to use a spudger to initially create separation between the screen and the casing.
Run this object around the perimeter of the tablet until there is separation between the casing and the screen.
Remove the back casing and set aside.

Remove the back casing from the screen by sliding a credit card or a similarly thin but firm object in between the casing and the screen.

You may need to use a spudger to initially create separation between the screen and the casing.

Run this object around the perimeter of the tablet until there is separation between the casing and the screen.

Remove the back casing and set aside.

Step 3

Peel tape off of ribbon connectors. Starting at the power button, work clockwise around the tablet.

Peel tape off of ribbon connectors. Starting at the power button, work clockwise around the tablet.

Step 4

To remove the camera ribbon cable, lift the flap using a spudger.
Pull the ribbon directly back to release it.

To remove the camera ribbon cable, lift the flap using a spudger.

Pull the ribbon directly back to release it.

Step 5

Remove the second ribbon cable by prying up the black flap using a spudger.
Pull the ribbon cable horizontally directly away from the battery.

Remove the second ribbon cable by prying up the black flap using a spudger.

Pull the ribbon cable horizontally directly away from the battery.

Step 6

Remove the final ribbon cable by pulling back the two black tabs on either side of the ribbon cable.
Pull the ribbon horizontally directly away from the battery.

Remove the final ribbon cable by pulling back the two black tabs on either side of the ribbon cable.

Pull the ribbon horizontally directly away from the battery.

Step 7

Unscrew the thirteen 4.75mm screws around the perimeter of the tablet using a PH 00 screwdriver.

Unscrew the thirteen 4.75mm screws around the perimeter of the tablet using a PH 00 screwdriver.

Step 8

Unscrew the four 3.75mm screws and plastic washers using a PH 00 screwdriver.
Lift up the circuit board.

Unscrew the four 3.75mm screws and plastic washers using a PH 00 screwdriver.

Lift up the circuit board.

Step 9

Unscrew the final two screws that were underneath the circuit board.
These screws are near the charging port and USB adapter.
These screws are also 3.75mm and can be interchanged with the second set of screws only.

Unscrew the final two screws that were underneath the circuit board.

These screws are near the charging port and USB adapter.

These screws are also 3.75mm and can be interchanged with the second set of screws only.

Step 10

Lift the circuit board and black internal mounting piece away from the screen.
Set the circuit board aside.
Be careful of the soldered antenna as you separate the pieces.
Be careful of the soldered ribbon that is connected to the power source. This ribbon is fragile.

Lift the circuit board and black internal mounting piece away from the screen.

Set the circuit board aside.

Be careful of the soldered antenna as you separate the pieces.

Be careful of the soldered ribbon that is connected to the power source. This ribbon is fragile.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors

                    Tyler Tyrrell

Member since: 03/11/2015

890 Reputation

                                      4 Guides authored                  



                       Badges:
                       17







                                                        +14 more badges

Team

                       Colorado Springs, Team 5-5, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 5-5, Panko Spring 2015 



                    UCCS-PANKO-S15S5G5                     


                                            3 Members                     


                                            12 Guides authored

Emmanuel - Apr 4, 2016

Whwre can i buy the new screen

William Henderson - Dec 21, 2017

I don’t see the ssd, and way to upgrade the internal sad had?

Introduction#

What you need#

Team#

Introduction

What you need

Team