Disassembling Ibm Thinkpad A30 Cpu Fan Repair Guide

Difficulty

Difficult

Steps

16

Time Required

                          15 minutes            

Sections

4

• Battery
• 1 step
• Upper Case
• 7 steps
• Display Assembly
• 5 steps
• CPU Fan
• 3 steps

Flags

2

Confusing Text

Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!

Missed a Step

Oops! This guide is currently missing some important steps.

• BackIBM ThinkPad A30

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Flip the ThinkPad over so that it is upside down.
• Slide the highlighted tab to the left.
• With your finger on the tab, remove the battery by lifting it upwards away from the laptop.

Flip the ThinkPad over so that it is upside down.

Slide the highlighted tab to the left.

With your finger on the tab, remove the battery by lifting it upwards away from the laptop.

1024

Step 2

              Upper Case               

• Make sure the laptop is upside down and oriented in the direction shown.
• Remove the six 16.7mm screws inside the circled holes.

Make sure the laptop is upside down and oriented in the direction shown.

Remove the six 16.7mm screws inside the circled holes.

Step 3

• Rotate the ThinkPad so that the hard drive bay is facing you.
• Remove the black cover to reveal a 14.8mm screw.
• Remove the uncovered screw with a Phillips #0 screwdriver.

Rotate the ThinkPad so that the hard drive bay is facing you.

Remove the black cover to reveal a 14.8mm screw.

Remove the uncovered screw with a Phillips #0 screwdriver.

Step 4

• Flip the ThinkPad over and open the LCD panel.
• Pry apart the keyboard with a plastic opening tool or with your fingers.

Flip the ThinkPad over and open the LCD panel.

Pry apart the keyboard with a plastic opening tool or with your fingers.

Step 5

• Be careful not to pull out the keyboard carelessly; there is a connector underneath it!
• Lift the front end of the keyboard as shown.
• Using your fingers, remove the black film cover.

Be careful not to pull out the keyboard carelessly; there is a connector underneath it!

Lift the front end of the keyboard as shown.

Using your fingers, remove the black film cover.

Step 6

• Locate the connector attached to the motherboard.
• Disconnect the ribbon cable by removing the connector.

Locate the connector attached to the motherboard.

Disconnect the ribbon cable by removing the connector.

Step 7

• Lift and remove the keyboard.
• Remove the two 5.6mm screws.
• Remove the 16.7mm screw.

Lift and remove the keyboard.

Remove the two 5.6mm screws.

Remove the 16.7mm screw.

Step 8

• You will need to use a little force. Be wary of the tabs.
• Pry off the upper case with your hands.

You will need to use a little force. Be wary of the tabs.

Pry off the upper case with your hands.

Step 9

              Display Assembly               

• Remove the 5.6mm screw that holds the LCD to the upper case.

Remove the 5.6mm screw that holds the LCD to the upper case.

Step 10

• Remove the 5.6mm screw on the left side of the three-pronged connector.
• Remove the other two 16.7mm screws.
• Lift and remove connector.

Remove the 5.6mm screw on the left side of the three-pronged connector.

Remove the other two 16.7mm screws.

Lift and remove connector.

Step 11

• Pull out the white tab connecting the LCD to the motherboard.

Pull out the white tab connecting the LCD to the motherboard.

Step 12

• Turn the laptop so that the back is facing you.
• Remove the four 5.6mm long screws.

Turn the laptop so that the back is facing you.

Remove the four 5.6mm long screws.

Step 13

• Place the laptop so that the LCD is facing you again.
• Gently lift the LCD monitor up and out.
• Remove the black plastic tab.

Place the laptop so that the LCD is facing you again.

Gently lift the LCD monitor up and out.

Remove the black plastic tab.

Step 14

              CPU Fan               

• Locate the 4 screws that will need to be removed.
• One screw (yellow) is observable. The three other screws (red) are below the heatsink bracket.
• Remove the 5.6mm (yellow) and three 16.1mm (red) screws.

Locate the 4 screws that will need to be removed.

One screw (yellow) is observable. The three other screws (red) are below the heatsink bracket.

Remove the 5.6mm (yellow) and three 16.1mm (red) screws.

Step 15

• Lift the heatsink bracket up.

Lift the heatsink bracket up.

Step 16

• Be careful not to pull too hard! There is a cable attached to the fan!
• Lift the fan/heatsink assembly up.
• Locate the fan power cable and pull upwards near the connector.
• Remove the fan/heatsink assembly.

Be careful not to pull too hard! There is a cable attached to the fan!

Lift the fan/heatsink assembly up.

Locate the fan power cable and pull upwards near the connector.

Remove the fan/heatsink assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 10 other contributors 

                    Jessica                     

Member since: 10/06/2010

162 Reputation

                                      7 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges                           

Team

                       Cal Poly, Team 4-44, Amido Fall 2010                        

                                                  Member of Cal Poly, Team 4-44, Amido Fall 2010 



                    CPSU-AMIDO-F10S4G44                     


                                            4 Members                     


                                            26 Guides authored