Disassembling Hp Photosmart C3180 Ink Cartridge Track Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Top Panel
9 steps
Disassembling HP Photosmart c3180 Ink Cartridge Track
13 steps

Flags

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

BackHP Photosmart C3180
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Top Panel

Before disassembling your printer, be sure that the printer has been unplugged.
Rotate the printer 90 degrees counter clockwise so that the side panel next to control panel is facing you.
Remove the two T10 12mm Torx screws from the left side panel.

Before disassembling your printer, be sure that the printer has been unplugged.

Rotate the printer 90 degrees counter clockwise so that the side panel next to control panel is facing you.

Remove the two T10 12mm Torx screws from the left side panel.

1024

Step 2

Firmly pull the the back of the side panel until it separates from the body of the printer.
Rotate the side panel upwards while pulling it towards yourself to remove the panel.

Firmly pull the the back of the side panel until it separates from the body of the printer.

Rotate the side panel upwards while pulling it towards yourself to remove the panel.

Step 3

Rotate the printer 90 degrees clockwise.
Grasp the paper tray and rotate it down.
Insert your fingers into the slot in the printer door and pull to rotate the gate down.

Rotate the printer 90 degrees clockwise.

Grasp the paper tray and rotate it down.

Insert your fingers into the slot in the printer door and pull to rotate the gate down.

Step 4

Rotate the printer 90 degrees clockwise.
Remove the two T10 12 mm Torx screws.
Grasp both sides of the side panel and pull it forward to remove the panel.

Remove the two T10 12 mm Torx screws.

Grasp both sides of the side panel and pull it forward to remove the panel.

Step 5

Rotate the printer 90 degrees counter clockwise.
Lift the scanner lid to expose the scanner glass.

Rotate the printer 90 degrees counter clockwise.

Lift the scanner lid to expose the scanner glass.

Step 6

Remove the two T10 12 mm Torx screws.
Do not attempt to lift the top panel off the printer yet because it is still connected to the printer body by a cable.

Do not attempt to lift the top panel off the printer yet because it is still connected to the printer body by a cable.

Step 7

Rotate the printer 90 degrees counter clockwise.
Inside the printer is a small white tab. Press it inward with a spudger until a pop is heard.
Remove the front panel by grasping its front and pulling away from the printer.

Inside the printer is a small white tab. Press it inward with a spudger until a pop is heard.

Remove the front panel by grasping its front and pulling away from the printer.

Step 8

Rotate the printer 90 degrees clockwise.
Remove the cable connecting the top panel of the printer to the power button assembly.

Remove the cable connecting the top panel of the printer to the power button assembly.

Step 9

Carefully lift the top panel of the printer away from the printer body.

Carefully lift the top panel of the printer away from the printer body.

Step 10

              Disassembling HP Photosmart c3180 Ink Cartridge Track

Set aside the top panel of the printer.
Remove the two T10 12 mm Torx screws from the top front of the printer

Set aside the top panel of the printer.

Remove the two T10 12 mm Torx screws from the top front of the printer

Step 11

Rotate the Printer 90 degrees counter clockwise.
Remove the scanner cable from the main circuit board.
Grasp the bottom of the cable and pull straight up. Do not wiggle it from side to side or twist it as this can damage the connection.

Rotate the Printer 90 degrees counter clockwise.

Remove the scanner cable from the main circuit board.

Grasp the bottom of the cable and pull straight up. Do not wiggle it from side to side or twist it as this can damage the connection.

Step 12

Rotate the printer 90 degrees clockwise.
Using both hands, lift the scanner tray from the body of the printer.

Using both hands, lift the scanner tray from the body of the printer.

Step 13

Remove the power button circuit board from the support frame by pinching the left side, and pulling forward and to the left simultaneously.
Push up on the tab holding the secondary control circuit board with the spudger and pull it forward to remove it.
Be careful not to pull too hard on the cable connecting the power button control circuit board and the secondary control circuit board to the main circuit board

Remove the power button circuit board from the support frame by pinching the left side, and pulling forward and to the left simultaneously.

Push up on the tab holding the secondary control circuit board with the spudger and pull it forward to remove it.

Be careful not to pull too hard on the cable connecting the power button control circuit board and the secondary control circuit board to the main circuit board

Step 14

Remove the two T10 12 mm Torx screws.
Lift the support frame off of the printer body with both hands.

Lift the support frame off of the printer body with both hands.

Step 15

Remove the printer door and paper tray by putting them in the closed position and not laying flat then rotating them upwards lift the left side up.

Remove the printer door and paper tray by putting them in the closed position and not laying flat then rotating them upwards lift the left side up.

Step 16

Remove both of the ink cartridges by grabbing the front of the ink cartridge and pulling down.
Make sure that the printer carriage is pushed all the way to the right.

Remove both of the ink cartridges by grabbing the front of the ink cartridge and pulling down.

Make sure that the printer carriage is pushed all the way to the right.

Step 17

Remove the T10 6 mm Torx screw on the left side of the track assembly.
Remove the T10 12 mm Torx screw on the left side of the track assembly.

Remove the T10 6 mm Torx screw on the left side of the track assembly.

Remove the T10 12 mm Torx screw on the left side of the track assembly.

Step 18

Gently push the ink cartridge carriage to the left side of the printer.

Gently push the ink cartridge carriage to the left side of the printer.

Step 19

Remove the two T10 12 mm Torx screws.
Remove the two T10 6 mm Torx screws.

Remove the two T10 6 mm Torx screws.

Step 20

Rotate the printer 90 degrees counter clockwise.
Remove the cable connecting the ink cartridge carriage to the main circuit board.
Pull straight up to free the cable from the main circuit board. Do not twist or wiggle the cable as doing so can damage it.
You may need to lift the carriage up with one hand in order to reach the cable with the free hand as shown.

Remove the cable connecting the ink cartridge carriage to the main circuit board.

Pull straight up to free the cable from the main circuit board. Do not twist or wiggle the cable as doing so can damage it.

You may need to lift the carriage up with one hand in order to reach the cable with the free hand as shown.

Step 21

Carefully remove the connector holding the drive motor wires to the main circuit board.

Carefully remove the connector holding the drive motor wires to the main circuit board.

Step 22

Slide the ink cartridge carriage all the way to the right side of the printer.
Using both hands, carefully lift the ink cartridge track off of the main body of the printer.

Slide the ink cartridge carriage all the way to the right side of the printer.

Using both hands, carefully lift the ink cartridge track off of the main body of the printer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                                      with 8 other contributors

Jim

Member since: 10/06/2011

1,452 Reputation

                                      10 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team 20-30, Maness Fall 2011                        

                                                  Member of Cal Poly, Team 20-30, Maness Fall 2011 



                    CPSU-MANESS-F11S20G30                     


                                            4 Members                     


                                            25 Guides authored

Knyte Spyder - Jul 3, 2020

Thank You sooo much….Just what I needed

One of the 4 pins on this spring loaded plastic piece on the carriage farthest one to the right popped off and for some reason it raised up and was stopping the carriage from sliding left..So once I got the carriage off it dropped back down ,spring is fine so I snapped the pin back in…cool i thought it was broken…So I’ll clean it up put it back together and see what happens

Sure hope I can get those cables back in rite

I’ll let you know!!! »—-@—->

Wpw its working

Got rid of the flashing orange light,carriage is sliding left an right ,printed a test page…WOOOHOOO!!!

Thank you all again so much

Markup Mishap#

What you need#

Team#

Markup Mishap

What you need

Team