Difficulty
Difficult
Steps
11
Time Required
20 - 30 minutes
Sections
1
- Outer Casing
- 11 steps
Flags
0
BackFujifilm Endeavor 100ix
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Casing
- Locate and remove two 6.4mm screws on the bottom of the camera with a Phillips #00 screwdriver.
Locate and remove two 6.4mm screws on the bottom of the camera with a Phillips #00 screwdriver.
1024
Step 2
- Locate the battery door.
Locate the battery door.
Step 3
- Locate the latch on the battery door marked by the word “BATT.” Use your finger to pry it open.
Locate the latch on the battery door marked by the word “BATT.” Use your finger to pry it open.
Step 4
- Remove the battery from the camera by pulling the battery door outwards.
Remove the battery from the camera by pulling the battery door outwards.
Step 5
- Locate and remove three black 3.80mm screws on the back of the camera with the Phillips #00 screwdriver.
Locate and remove three black 3.80mm screws on the back of the camera with the Phillips #00 screwdriver.
Step 6
- Locate and remove the 6.4mm screws located on either side of the camera with a Phillips #00 screwdriver.
Locate and remove the 6.4mm screws located on either side of the camera with a Phillips #00 screwdriver.
Step 7
- Locate the film door latch located on the side of the camera.
- Insert the spudger under the latch.
- Caution: Be careful during the following step in order to not break any parts within the camera. Prying the latch in any other direction than perpendicular may result in broken parts.
- Pry the latch upward, applying force perpendicular to the camera.
Locate the film door latch located on the side of the camera.
Insert the spudger under the latch.
Caution: Be careful during the following step in order to not break any parts within the camera. Prying the latch in any other direction than perpendicular may result in broken parts.
Pry the latch upward, applying force perpendicular to the camera.
Step 8
- Insert the flat edge of the spudger between the gold front casing and the black back casing.
- Pry the spudger upward until the black back casing snaps out and is dislodged on that edge of the camera.
Insert the flat edge of the spudger between the gold front casing and the black back casing.
Pry the spudger upward until the black back casing snaps out and is dislodged on that edge of the camera.
Step 9
- Squeeze the camera by placing a thumb on the tab marked CE.
- Pull the back half of the camera firmly away from the camera body.
Squeeze the camera by placing a thumb on the tab marked CE.
Pull the back half of the camera firmly away from the camera body.
Step 10
- Locate and remove the 3.80mm screw inside the film compartment with the Phillips #00 screwdriver.
Locate and remove the 3.80mm screw inside the film compartment with the Phillips #00 screwdriver.
Step 11
- Pull the front cover off of the camera by lifting the tripod tab over the tripod hole.
Pull the front cover off of the camera by lifting the tripod tab over the tripod hole.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Eric Nicolai
Member since: 01/10/2011
679 Reputation
6 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 13-5, Forte Winter 2011
Member of Cal Poly, Team 13-5, Forte Winter 2011
CPSU-FORTE-W11S13G5
5 Members
11 Guides authored
