Difficulty
Moderate
Steps
9
Time Required
Suggest a time??
Sections
2
- Disassembling Epson PPC650 Camera Casing
- 5 steps
- Disassembling Epson PPC650 Replacing Flash
- 4 steps
Flags
4
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Better Introduction
Improve this guide by completing or revising its introduction.
BackEpson PhotoPC 650
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Disassembling Epson PPC650 Camera Casing
- Make sure the camera is turned off here.
- Remove batteries from the battery compartment located on the bottom of the camera
- Remove SD card for the card reader compartment located on the flat side (left side) of the camera
Make sure the camera is turned off here.
Remove batteries from the battery compartment located on the bottom of the camera
Remove SD card for the card reader compartment located on the flat side (left side) of the camera
1024
Step 2
- Remove 2 screws on the rounded side of the camera wisdom here.
Remove 2 screws on the rounded side of the camera wisdom here.
Step 3
- Remove 3 screws on the flat side of the camera
- All silver screws go into the side of the camera that is silver
- All black screws go into the side of the camera that is black
Remove 3 screws on the flat side of the camera
All silver screws go into the side of the camera that is silver
All black screws go into the side of the camera that is black
Step 4
- Remove 4 screws from the bottom of the camera
- All silver screws go into the side of the camera that is silver
- All black screws go into the side of the camera that is black
Remove 4 screws from the bottom of the camera
Step 5
- Separate the front and back pieces of the cameras plastic casing using a spudgerm here.
- WARNING: When pulling the front plastic casing, be careful of the wire that are connected to the aperture control
- Use minimal force so that the plastic casing does not break
- When separating the small silver sliding indicator for view/off/playback may fall out
- The plastic viewing window located on the top of the camera may also become lose and fall out
Separate the front and back pieces of the cameras plastic casing using a spudgerm here.
WARNING: When pulling the front plastic casing, be careful of the wire that are connected to the aperture control
Use minimal force so that the plastic casing does not break
When separating the small silver sliding indicator for view/off/playback may fall out
The plastic viewing window located on the top of the camera may also become lose and fall out
Step 6
Disassembling Epson PPC650 Replacing Flash
- Optional: Remove two black screws from top of camera on the flash side for more working space.
Optional: Remove two black screws from top of camera on the flash side for more working space.
Step 7
- Remove clear rubber band holding flash in line with wiring.
Remove clear rubber band holding flash in line with wiring.
Step 8
- Cut white wire, red wire, and black wire connecting flash element to circuit board by unsoldering ends
Cut white wire, red wire, and black wire connecting flash element to circuit board by unsoldering ends
Step 9
- Connect new flash by soldering copper ends to their respective ends to new flash element.
Connect new flash by soldering copper ends to their respective ends to new flash element.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Xan Danes
Member since: 02/14/2013
116 Reputation
1 Guide authored
Badges:
3
Team
Ohio State, Team 1-5, Buehl Spring 2013
Member of Ohio State, Team 1-5, Buehl Spring 2013
OSU-BUEHL-S13S1G5
4 Members
3 Guides authored
