Difficulty

Easy

Steps

14

Time Required

                          1 minute

Sections

6

  • Battery
  • 2 steps
  • RAM
  • 2 steps
  • Keyboard
  • 4 steps
  • Top Cover
  • 3 steps
  • Hard Drive
  • 2 steps
  • Fan
  • 1 step

Flags

2

Missed a Step

Oops! This guide is currently missing some important steps.

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

  • BackCompaq Mini 110

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Locate the battery and the battery tabs on the bottom of the Compaq Mini.

Locate the battery and the battery tabs on the bottom of the Compaq Mini.

1024

Step 2

  • Push both tabs inward simultaneously and slide the battery out.

Push both tabs inward simultaneously and slide the battery out.

Step 3

              RAM
  • Use a Philips #0 screwdriver to unscrew the two screws covering the memory compartment on the bottom of the laptop and remove the cover.

Use a Philips #0 screwdriver to unscrew the two screws covering the memory compartment on the bottom of the laptop and remove the cover.

Step 4

  • Push out the side tabs simultaneously and pull out the old RAM module.
  • When inserting a new RAM stick, be sure to evenly insert the gold pins in the same orientation that the old module was removed. While sliding the module in, press the side tabs in place.

Push out the side tabs simultaneously and pull out the old RAM module.

When inserting a new RAM stick, be sure to evenly insert the gold pins in the same orientation that the old module was removed. While sliding the module in, press the side tabs in place.

Step 5

              Keyboard
  • Remove the rubber pads located on the corners of your Compaq Mini.
  • There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

Remove the rubber pads located on the corners of your Compaq Mini.

There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

Step 6

  • Unscrew all the corner screws. There are four total, one under each rubber pad.

Unscrew all the corner screws. There are four total, one under each rubber pad.

Step 7

  • Unscrew the screw for the bottom case located in the RAM compartment.

Unscrew the screw for the bottom case located in the RAM compartment.

Step 8

  • Remove the three screws in the silver tabs at the back of the keyboard.
  • These are located at the back of the base under the screen.
  • Lift the keyboard away from the laptop.

Remove the three screws in the silver tabs at the back of the keyboard.

These are located at the back of the base under the screen.

Lift the keyboard away from the laptop.

Step 9

              Top Cover
  • Remove the eight screws that are from the plastic top cover.

Remove the eight screws that are from the plastic top cover.

Step 10

  • Pry up the top plastic cover using a spudger.
  • These two tabs under the screen need to be pushed in with a spudger.

Pry up the top plastic cover using a spudger.

These two tabs under the screen need to be pushed in with a spudger.

Step 11

  • Remove the cable by carefully pulling it up.
  • Be careful when lifting up the cover because the track pad is still attached.

Remove the cable by carefully pulling it up.

Be careful when lifting up the cover because the track pad is still attached.

Step 12

              Hard Drive
  • Remove the three screws holding the panel in place.

Remove the three screws holding the panel in place.

Step 13

  • Pull up on the tab to remove the hard drive.

Pull up on the tab to remove the hard drive.

Step 14

              Fan
  • Remove the two screws holding the fan in place.
  • There is still a cable attached to the fan so be sure to pull that out as well.

Remove the two screws holding the fan in place.

There is still a cable attached to the fan so be sure to pull that out as well.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors 


                    alea

Member since: 10/06/2010

1,393 Reputation

                                      14 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 22-2, Maness Fall 2010                        

                                                  Member of Cal Poly, Team 22-2, Maness Fall 2010 



                    CPSU-MANESS-F10S22G2                     


                                            6 Members                     


                                            20 Guides authored