Featured

Featured Guide

Difficulty

Moderate

Steps

10

Time Required

                          15 - 20 minutes

Sections

3

  • Back Cover
  • 4 steps
  • LCD Assembly
  • 4 steps
  • LCD Display
  • 2 steps

Flags

1

This guide has been found to be exceptionally cool by the iFixit staff.

  • BackCanon PowerShot SD800 IS

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Remove one 2.25mm screw on the bottom.

Remove one 2.25mm screw on the bottom.

1024

Step 2

  • Remove two 2.25mm screws on the right side looking from the front.

Remove two 2.25mm screws on the right side looking from the front.

Step 3

  • Remove one 4.7mm screw on the side with the AV output.

Remove one 4.7mm screw on the side with the AV output.

Step 4

  • Pull off the back cover.
  • The back cover tends to stick in the top corner (near the mode dial) due to a metal clip. Jiggle the cover side to side as you pull it out.

Pull off the back cover.

The back cover tends to stick in the top corner (near the mode dial) due to a metal clip. Jiggle the cover side to side as you pull it out.

Step 5

              LCD Assembly
  • Remove 2 2.4mm screws on bottom.

Remove 2 2.4mm screws on bottom.

Step 6

  • Follow the small data cable to where it connects to the camera.
  • Lift the back white portion to unlock the cable.
  • The cable should easily slide out.
  • The connector is very fragile. Use caution when lifting the lock.

Follow the small data cable to where it connects to the camera.

Lift the back white portion to unlock the cable.

The cable should easily slide out.

The connector is very fragile. Use caution when lifting the lock.

Step 7

  • Gently lift LCD display off.
  • There will be two data cables still attached to the camera. Do not break them.
  • There may be a loose strip of metal along the inner side of the LCD display for a secure fit.

Gently lift LCD display off.

There will be two data cables still attached to the camera. Do not break them.

There may be a loose strip of metal along the inner side of the LCD display for a secure fit.

Step 8

  • Follow the larger cable to where it connects to the camera.
  • Lift the front black portion of the connector to unlock the data cable.
  • The cable should easily slide out.
  • The connector is very fragile. Use caution when lifting the lock.

Follow the larger cable to where it connects to the camera.

Lift the front black portion of the connector to unlock the data cable.

Step 9

              LCD Display
  • Pry the LCD display out from the four metal clamps.

Pry the LCD display out from the four metal clamps.

Step 10

  • To remove the LCD, peel the larger data cable off from the frame.
  • The LCD is glued by its data cable to the back of the LCD frame.

To remove the LCD, peel the larger data cable off from the frame.

The LCD is glued by its data cable to the back of the LCD frame.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Jeremy Rabaino

Member since: 10/10/2010

135 Reputation

                                      6 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team 20-9, Maness Fall 2010                        

                                                  Member of Cal Poly, Team 20-9, Maness Fall 2010 



                    CPSU-MANESS-F10S20G9                     


                                            5 Members                     


                                            6 Guides authored