Disassembling Asus Eee Pc 1008Ha Repair Guide

Difficulty

Difficult

Steps

Time Required

                          20 minutes

Sections

Disassembling ASUS Eee pc 1008Ha
13 steps

Flags

BackAsus Eee PC 1008ha
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Disassembling ASUS Eee pc 1008Ha

Turn off the computer.
Disconnect the charging cable from the computer.
Failure to unplug the cable could result in electric shock.
Top Panel: Use a Plastic Opening Tool to carefully pry the top panel from the base.

Turn off the computer.

Disconnect the charging cable from the computer.

Failure to unplug the cable could result in electric shock.

Top Panel: Use a Plastic Opening Tool to carefully pry the top panel from the base.

1024

Step 2

Keyboard: Lift the side of the keyboard gently and disconnect the attached ribbon located underneath the keyboard.
Place your index finger in the hole on the right side of the keyboard tray and lift the tray gently.

Keyboard: Lift the side of the keyboard gently and disconnect the attached ribbon located underneath the keyboard.

Place your index finger in the hole on the right side of the keyboard tray and lift the tray gently.

Step 3

Battery: Use your fingers to lift the battery and gently disconnect the wires from the base.

Battery: Use your fingers to lift the battery and gently disconnect the wires from the base.

Step 4

Heat sink: Use a Phillips head screwdriver to unscrew the screws that connect the heat sink to the fan.
Use a Flathead Screwdriver to gently lift the copper heat sink and use your fingers to remove it from the laptop.

Heat sink: Use a Phillips head screwdriver to unscrew the screws that connect the heat sink to the fan.

Use a Flathead Screwdriver to gently lift the copper heat sink and use your fingers to remove it from the laptop.

Step 5

Fan: Unscrew the screws that secure the fan.
Use your fingers to lift the fan and pull the white plug carefully from the motherboard.

Fan: Unscrew the screws that secure the fan.

Use your fingers to lift the fan and pull the white plug carefully from the motherboard.

Step 6

USB header card: Use the Phillips head screwdriver to unscrew the 3 screws from the USB header card.

USB header card: Use the Phillips head screwdriver to unscrew the 3 screws from the USB header card.

Step 7

Use your fingers to pull the USB header card from the side of the device chassis. (The USB header card will remain attached by wires.)

Use your fingers to pull the USB header card from the side of the device chassis. (The USB header card will remain attached by wires.)

Step 8

Screen: Hold the USB header card in one hand.
Use your other hand to unscrew the 4 screws (2 on each side) that attach the screen to the base.

Screen: Hold the USB header card in one hand.

Use your other hand to unscrew the 4 screws (2 on each side) that attach the screen to the base.

Step 9

Use your fingers to hold the screen and carefully disconnect it from the right side of the base.
Loosen the screen from the left side of the base.

Use your fingers to hold the screen and carefully disconnect it from the right side of the base.

Loosen the screen from the left side of the base.

Step 10

Use a Flathead Screwdriver to pry off the chits from the front panel. (The chits are the small black rubber caps.)
Unscrew the screws that connect the front panel of the screen.

Use a Flathead Screwdriver to pry off the chits from the front panel. (The chits are the small black rubber caps.)

Unscrew the screws that connect the front panel of the screen.

Step 11

Slide the Plastic Opening Tool under the edge of the screen bezel to release the front panel of the screen.

Slide the Plastic Opening Tool under the edge of the screen bezel to release the front panel of the screen.

Step 12

Unscrew the screws from the edge of the screen.
Use your fingers to hold the screen and remove it from the base. (Wires will still be attached between the screen and the motherboard.)

Unscrew the screws from the edge of the screen.

Use your fingers to hold the screen and remove it from the base. (Wires will still be attached between the screen and the motherboard.)

Step 13

Use your fingers to remove the adhesive tape located on the back of the screen near the wire connection.
Disconnect the wire from the screen.

Use your fingers to remove the adhesive tape located on the back of the screen near the wire connection.

Disconnect the wire from the screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 9 other contributors

Leo

Member since: 04/18/2013

183 Reputation

                                      1 Guide authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 21-52, Johann Spring 2013                        

                                                  Member of Cal Poly, Team 21-52, Johann Spring 2013 



                    CPSU-JOHANN-S13S21G52                     


                                            4 Members                     


                                            11 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team