Difficulty
Moderate
Steps
5
Time Required
15 minutes
Sections
1
- Charging Port
- 5 steps
Flags
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
BackDigitac Jazz Ultratab C725
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Charging Port
- Locate the four 3.5 mm Phillips head screws holding the silver back plate and the screen together. There are 2 screws on the top and another 2 screws on the bottom.
- Remove all four screws with the Phillips #00 screwdriver.
- Remove the screws with the least amount of force. The removal of the screw will be more difficult if thread damage occurs.
Locate the four 3.5 mm Phillips head screws holding the silver back plate and the screen together. There are 2 screws on the top and another 2 screws on the bottom.
Remove all four screws with the Phillips #00 screwdriver.
Remove the screws with the least amount of force. The removal of the screw will be more difficult if thread damage occurs.
1024
Step 2
- Flip your device so that the long side without the buttons is facing you.
- Insert the plastic opening tool between the silver back plate and the screen. From the corner of the device on either side, pry the seam of the device about 1 inch.
- With the plastic opening tool, pry the screen apart from the back plate.
- Keep prying the screen apart from the back plate until they are separated.
- With the plastic opening tool, if necessary, pry apart the remaining seams of the device.
- After the screen is loose, pull the screen towards you. Lift it to prevent damage to the buttons.
Flip your device so that the long side without the buttons is facing you.
Insert the plastic opening tool between the silver back plate and the screen. From the corner of the device on either side, pry the seam of the device about 1 inch.
With the plastic opening tool, pry the screen apart from the back plate.
Keep prying the screen apart from the back plate until they are separated.
With the plastic opening tool, if necessary, pry apart the remaining seams of the device.
After the screen is loose, pull the screen towards you. Lift it to prevent damage to the buttons.
Step 3
- Locate the 3 black clips on the motherboard that hold the data cables./
- Using the Spudger, pry the black clips up to a 90 degree angle./
- Pull the data cables out once the clips are up to a 90 degree angle.
- Repeat this for all 3 clips.
Locate the 3 black clips on the motherboard that hold the data cables./
Using the Spudger, pry the black clips up to a 90 degree angle./
Pull the data cables out once the clips are up to a 90 degree angle.
Repeat this for all 3 clips.
Step 4
- Locate the two 4.0 mm Phillips head screws that are holding the motherboard in place.
- Use the Phillips #00 screwdriver to remove both of the screws.
Locate the two 4.0 mm Phillips head screws that are holding the motherboard in place.
Use the Phillips #00 screwdriver to remove both of the screws.
Step 5
- The motherboard should now be loose.
- To gain access to the charging port, flip the motherboard over.
- Use the tweezers to pull the charging port off of the motherboard.
The motherboard should now be loose.
To gain access to the charging port, flip the motherboard over.
Use the tweezers to pull the charging port off of the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 5 other contributors
Savannah Brazzeal
Member since: 01/20/2015
300 Reputation
2 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 11-6, Blackwell Winter 2015
Member of USF Tampa, Team 11-6, Blackwell Winter 2015
USFT-BLACKWELL-W15S11G6
2 Members
5 Guides authored
