Digiland Dl1010Q Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Rear Case
3 steps
Battery
3 steps
Screen
3 steps

Flags

BackDigiLand DL1010Q
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Safely remove and put back together your deviceAccurately replace the screen of your device

What you need

Step 1

              Rear Case

With a J00 Philips head screwdriver, unscrew the two 4mm black screws located at the bottom of the device.
Before disassembling your device, be sure it is powered off.

With a J00 Philips head screwdriver, unscrew the two 4mm black screws located at the bottom of the device.

Before disassembling your device, be sure it is powered off.

1024

Step 2

Using a plastic opening tool, begin softly prying open device by first inserting it in between the front and back panels.
Continue prying the edges while moving around the device’s perimeter until the back can be easily removed.

Using a plastic opening tool, begin softly prying open device by first inserting it in between the front and back panels.

Continue prying the edges while moving around the device’s perimeter until the back can be easily removed.

Step 3

Carefully lift back panel away from the body of the device.
Speaker wires are connected to both the front and back panel.

Carefully lift back panel away from the body of the device.

Speaker wires are connected to both the front and back panel.

Step 4

              Battery

Desolder positive and negative, red and black, wires from the mother board that are connected to the battery.
The soldering tool is hot, and will burn. For how to use a soldering tool follow the How to Solder Guide

Desolder positive and negative, red and black, wires from the mother board that are connected to the battery.

The soldering tool is hot, and will burn. For how to use a soldering tool follow the How to Solder Guide

Step 5

Using a metal spudger tool, wedge between battery and metal screen.
Follow the edge of the battery to loosen the glue.

Using a metal spudger tool, wedge between battery and metal screen.

Follow the edge of the battery to loosen the glue.

Step 6

Once the glue is loosened, you should be able to pry off the battery from the screen.
Using your hands, pull up on the battery to pull battery off.
Pulling on the battery causes you to bend the battery. Bending the battery could cause it to break open. Battery fumes are toxic and unsafe.
The battery will be completely disconnected and you can set the battery aside in a safe place.

Once the glue is loosened, you should be able to pry off the battery from the screen.

Using your hands, pull up on the battery to pull battery off.

Pulling on the battery causes you to bend the battery. Bending the battery could cause it to break open. Battery fumes are toxic and unsafe.

The battery will be completely disconnected and you can set the battery aside in a safe place.

Step 7

              Screen

Begin by locating the four 3mm silver screws that are holding the screen down to the digitizer. Set screws to the side.

Begin by locating the four 3mm silver screws that are holding the screen down to the digitizer. Set screws to the side.

Step 8

Once everything is removed, take one plastic opening tool and pry it between the screen and digitizer.

Once everything is removed, take one plastic opening tool and pry it between the screen and digitizer.

Step 9

Once the screen is pried free from the digitizer, simply grab the thin orange circuit strip and carefully pull in an upwards motion to remove the screen from the digitizer. Set screen to the side.

Once the screen is pried free from the digitizer, simply grab the thin orange circuit strip and carefully pull in an upwards motion to remove the screen from the digitizer. Set screen to the side.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 1 other contributor

                    Marissa Saidy

Member since: 09/28/2015

354 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Eastern Washington University, Team 1-5, Matresse Fall 2015                        

                                                  Member of Eastern Washington University, Team 1-5, Matresse Fall 2015 



                    EWU-MATRESSE-F15S1G5                     


                                            4 Members                     


                                            10 Guides authored

kevinosborn - Aug 31, 2016

I find it’s not necessary to remove the batttery, but there are scews holding down the main circuit board that he left out.

mardynie1234 - Oct 28, 2016

នៅណាមានបង

ខ្ញុំទិញមួយ

ផ្ញើតាមឡានបានអត់

ខ្ញិំនៅតាកែវ ស្រុកកោះអណ្ដែត

deavon davis - Nov 10, 2016

@kevinosborn hi

Introduction#

What you need#

Team#

Introduction

What you need

Team