Difficulty

Easy

Steps

16

Time Required

                          5 minutes

Sections

1

  • Motor
  • 16 steps

Flags

3

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackCorded jigsaw Dexter 750W - 750JS3-100.5

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Unplug
  • Before you begin, remember to disconnect the mains plug.

Before you begin, remember to disconnect the mains plug.

1024

Step 2

  • Remove the vacuum adapter from the back of the device.

Remove the vacuum adapter from the back of the device.

Step 3

  • Using a screwdriver or screwdriver, unscrew and open the device.
  • Unlock the tray by lifting the lever.

Using a screwdriver or screwdriver, unscrew and open the device.

Unlock the tray by lifting the lever.

Step 4

  • Use needle nose pliers and remove the clip located next to the blade holder.

Use needle nose pliers and remove the clip located next to the blade holder.

Step 5

  • Remove the blade holder, keeping the slider at the end of the holder.

Remove the blade holder, keeping the slider at the end of the holder.

Step 6

  • Unscrew the two screws and set them aside.

Unscrew the two screws and set them aside.

Step 7

  • Remove the two carbons located next to the stator.

Remove the two carbons located next to the stator.

Step 8

  • Lift the stator, then lever out the motor.

Lift the stator, then lever out the motor.

Step 9

  • Put the new motor back in its place.

Put the new motor back in its place.

Step 10

  • Collect the end cap on the old engine.
  • Put it back on the new motor.
  • Put some grease on the tip.

Collect the end cap on the old engine.

Put it back on the new motor.

Put some grease on the tip.

Step 11

  • Replace the two screws to stabilize the motor.

Replace the two screws to stabilize the motor.

Step 12

  • Return the blade holder to its location
  • Make sure you put each piece in its place.

Return the blade holder to its location

Make sure you put each piece in its place.

Step 13

  • Replace the staple in the same location. The curved side of the staple should go to the rounded side of the bracket.
  • Lubricate the whole
  • Make sure you put each piece in its place.

Replace the staple in the same location. The curved side of the staple should go to the rounded side of the bracket.

Lubricate the whole

Step 14

  • Put the coals back in their places.

Put the coals back in their places.

Step 15

  • Before closing, lubricate each gear.

Before closing, lubricate each gear.

Step 16

  • Close and screw the device.

Close and screw the device.

follow guide through or in reverse to reassemble

Cancel: I did not complete this guide.

        HelloMacOS is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

HelloMacOS

Author

                                      with 1 other contributor 


                    Céline Chemineau

Member since: 01/29/2020

16,042 Reputation

                                      95 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Leroy Merlin                        

                                                  Member of Leroy Merlin 



                    Community                     


                                            36 Members                     


                                            223 Guides authored