Difficulty
Difficult
Steps
12
Time Required
15 minutes
Sections
1
- LED
- 12 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackCorded multifunction sander Dexter 220W - 220MFS2.5
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Unplug
- Before you begin, remember to disconnect the mains plug.
Before you begin, remember to disconnect the mains plug.
1024
Step 2
- Remove the seal on the back of the device.
Remove the seal on the back of the device.
Step 3
- Unscrew the first screw of the pad.
- Then unscrew the four remaining screws and pull up to remove it.
- Finally remove the screws located on the hull of the device.
Unscrew the first screw of the pad.
Then unscrew the four remaining screws and pull up to remove it.
Finally remove the screws located on the hull of the device.
Step 4
- This step is the same for both carbons.
- Wedge the two carbons to be able to take out the rotor. Reassemble them with a screwdriver, then with another screwdriver press the tab.
- Lift the carbon and with the other tip of the screwdriver, twist the small leg.
- Then remove the carbon.
This step is the same for both carbons.
Wedge the two carbons to be able to take out the rotor. Reassemble them with a screwdriver, then with another screwdriver press the tab.
Lift the carbon and with the other tip of the screwdriver, twist the small leg.
Then remove the carbon.
Step 5
- Remove the rotor by lifting the frame to be able to retrieve it more easily.
Remove the rotor by lifting the frame to be able to retrieve it more easily.
Step 6
- Pull out the switch for more space.
Pull out the switch for more space.
Step 7
- Remove the LED from its housing using pliers
Remove the LED from its housing using pliers
Step 8
- Desolder the two black and red wires to be able to change the part.
Desolder the two black and red wires to be able to change the part.
Step 9
- Resolder the new LED.
- Then replace the LED in its housing, taking care to put the cables back in their path.
Resolder the new LED.
Then replace the LED in its housing, taking care to put the cables back in their path.
Step 10
- Replace the switch, the rotor in its housing. and unlock the carbons.
Replace the switch, the rotor in its housing. and unlock the carbons.
Step 11
- Replace the cable, the sheath must arrive between the two studs and the sleeve must be positioned in its housing.
- Replace the shell of the sander, taking care to position the stabilizers correctly in their housings.
- Finally remove the screws located on the hull of the device.
Replace the cable, the sheath must arrive between the two studs and the sleeve must be positioned in its housing.
Replace the shell of the sander, taking care to position the stabilizers correctly in their housings.
Step 12
- Replace the pad by positioning it perfectly in the tips.
- Tighten the four screws.
- Then the last screw. Finally put the gasket back in place.
Replace the pad by positioning it perfectly in the tips.
Tighten the four screws.
Then the last screw. Finally put the gasket back in place.
By the end of the guide you will have successfully replaced the LED.
To reassemble preform the steps in reverse.
Cancel: I did not complete this guide.
HelloMacOS is helping us fix the world! Want to contribute? Start translating ›
Special thanks to these translators:
100%
HelloMacOS
Author
with 1 other contributor
Céline Chemineau
Member since: 01/29/2020
16,042 Reputation
95 Guides authored
Badges:
11
+8 more badges
Team
Leroy Merlin
Member of Leroy Merlin
Community
36 Members
223 Guides authored
