Difficulty
Moderate
Steps
12
Time Required
5 - 10 minutes
Sections
4
- Back Cover
- 2 steps
- Power Cord
- 4 steps
- Brushes
- 2 steps
- Lever Assembly
- 4 steps
Flags
0
BackDeWALT Hammer Drill DW511
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Caution should be taken when working with the drill. It needs to be unplugged before working on any part of it.
What you need
Step 1
Back Cover
- Remove three 19 mm T20 Torx screws from the back of the drill.
Remove three 19 mm T20 Torx screws from the back of the drill.
1024
Step 2
- Place an opening tool in the groove line of the handle and pop the back loose.
- Grab the drill with two hands and pull the cover off.
Place an opening tool in the groove line of the handle and pop the back loose.
Grab the drill with two hands and pull the cover off.
Step 3
Power Cord
- Firmly grab the body of the trigger.
- Slowly pull the trigger until the entire body is out and only attached by wires.
Firmly grab the body of the trigger.
Slowly pull the trigger until the entire body is out and only attached by wires.
Step 4
- With sharp point tweezers, push the little metal flap up in the hole holding the wire.
- Clamp the wire with blunt tweezers, and slowly pull the wire out.
With sharp point tweezers, push the little metal flap up in the hole holding the wire.
Clamp the wire with blunt tweezers, and slowly pull the wire out.
Step 5
- With a pair of blunt nose tweezers, grab the white wire.
- Carefully wiggle the wire loose.
- Pull the wire slowly until it comes out.
With a pair of blunt nose tweezers, grab the white wire.
Carefully wiggle the wire loose.
Pull the wire slowly until it comes out.
Step 6
- With both wires free, the power cord is free from the trigger body.
With both wires free, the power cord is free from the trigger body.
Step 7
Brushes
- Use an opening tool to lift up the spring holding down the brush.
- Remove the brush from its holding.
Use an opening tool to lift up the spring holding down the brush.
Remove the brush from its holding.
Step 8
- With a pair of blunt nose tweezers, grab the red wire.
- Carefully wiggle the wire loose.
- Pull the wire slowly until it comes out.
With a pair of blunt nose tweezers, grab the red wire.
Step 9
Lever Assembly
- Remove two 45 mm T20 Torx screws.
- Remove one 30 mm T20 Torx screw.
Remove two 45 mm T20 Torx screws.
Remove one 30 mm T20 Torx screw.
Step 10
- Pull off the top case and set it aside.
Pull off the top case and set it aside.
Step 11
- Grab the gear case cover and gently pull it out just enough to where it exposes the lever assembly.
- It is important that the brushes are removed before you do this step or you may damage your brushes.
- The lever assembly can now be lifted out.
Grab the gear case cover and gently pull it out just enough to where it exposes the lever assembly.
It is important that the brushes are removed before you do this step or you may damage your brushes.
The lever assembly can now be lifted out.
Step 12
- With the old lever assembly removed you can now replace it with a new one.
With the old lever assembly removed you can now replace it with a new one.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Kodiak Kunder
Member since: 10/03/2019
180 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
Eastern Washington University, Team S1-G3, Al-Hmeyrat Fall 2019
Member of Eastern Washington University, Team S1-G3, Al-Hmeyrat Fall 2019
EWU-AL-HMEYRAT-F19S1G3
3 Members
5 Guides authored
