Dewalt Dwd112 Field Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Power Cord
7 steps
Armature
4 steps
Field
2 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

BackDeWalt DWD112
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Power Cord

Remove seven TR20 Torx Security screws from the side of the drill.

Remove seven TR20 Torx Security screws from the side of the drill.

1024

Step 2

Remove the top cover to reveal the inside of the drill.
Set the top cover of the drill aside.

Remove the top cover to reveal the inside of the drill.

Set the top cover of the drill aside.

Step 3

The power cord and the trigger act as a single part and must be replaced together.
Using one hand grab the trigger box and with the other grab the end of the wire connecting to the trigger box and disconnect the wire.

The power cord and the trigger act as a single part and must be replaced together.

Using one hand grab the trigger box and with the other grab the end of the wire connecting to the trigger box and disconnect the wire.

Step 4

Disconnect the second connected wire from the top of the trigger box.

Disconnect the second connected wire from the top of the trigger box.

Step 5

Lift the trigger box up to reveal the bottom side.
Disconnect the first connected wire from the bottom of the trigger box.

Lift the trigger box up to reveal the bottom side.

Disconnect the first connected wire from the bottom of the trigger box.

Step 6

Disconnect the last wire from the trigger box using the same method from the previous step.

Disconnect the last wire from the trigger box using the same method from the previous step.

Step 7

After all four wires are disconnected, the trigger and power cord are separated from the drill.
The power cord and trigger can be set aside if further disassembly is required.

After all four wires are disconnected, the trigger and power cord are separated from the drill.

The power cord and trigger can be set aside if further disassembly is required.

Step 8

              Armature

Take note of the keyless chuck and the meshing of the gears.

Take note of the keyless chuck and the meshing of the gears.

Step 9

Grab the metal chuck by the rotating spindle as if you are to tighten in a drill bit.
Lift the metal chuck out of its resting place and set aside.

Grab the metal chuck by the rotating spindle as if you are to tighten in a drill bit.

Lift the metal chuck out of its resting place and set aside.

Step 10

With your left hand, grab hold of the field, which is the large metal block with coils looped around the inside.
Use your other hand to take the bearing out from the end of the gear connected to the armature.

With your left hand, grab hold of the field, which is the large metal block with coils looped around the inside.

Use your other hand to take the bearing out from the end of the gear connected to the armature.

Step 11

Lift the field up once more with one hand and grab the cooling fan with the other hand and gently slide the armature out of the field.
The brushes will now be disconnected from the armature, meaning no current can flow from the power cord to the motor.

Lift the field up once more with one hand and grab the cooling fan with the other hand and gently slide the armature out of the field.

The brushes will now be disconnected from the armature, meaning no current can flow from the power cord to the motor.

Step 12

              Field

Move the black wire clear from any obstruction.
Repeat this step for the white wire and the red wire.

Move the black wire clear from any obstruction.

Repeat this step for the white wire and the red wire.

Step 13

The field is disconnected from all other parts.
Grab the field and gently lift it out of the case.

The field is disconnected from all other parts.

Grab the field and gently lift it out of the case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Samantha McSweeney

Member since: 03/07/2016

407 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UMass Dartmouth, Team 2-3, Isaacson Spring 2016                        

                                                  Member of UMass Dartmouth, Team 2-3, Isaacson Spring 2016 



                    UMASSD-ISAACSON-S16S2G3                     


                                            3 Members                     


                                            6 Guides authored

Jorge Diaz Viera - Aug 2, 2016

as a recommendation aimed at some or mark with a piece of ribbon cables disconnected the trigger with the contact number that corresponds to the rearm the drill going to not reverse the change control rotation.

Slice and Dice#

Introduction#

What you need#

Team#

Slice and Dice

Introduction

What you need

Team