Difficulty

Moderate

Steps

10

Time Required

                          15 - 20 minutes

Sections

3

  • Disassembling DeWalt D28110 Gear Case
  • 2 steps
  • Disassembling DeWalt D28110 Back Panel Disassembly
  • 4 steps
  • Power Switch
  • 4 steps

Flags

0

  • BackDeWalt D28110

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disassembling DeWalt D28110 Gear Case
  • Using the T-15 screwdriver, remove the four 22-mm torx screws on the gear case.
  • Unplug the grinder before any disassembly.

Using the T-15 screwdriver, remove the four 22-mm torx screws on the gear case.

Unplug the grinder before any disassembly.

1024

Step 2

  • Pull out the gear case.

Pull out the gear case.

Step 3

              Disassembling DeWalt D28110 Back Panel Disassembly
  • Using the T-15 screwdriver, remove the four 22-mm torx screws holding the back panel in place.
  • Unplug the grinder before any disassembly.

Using the T-15 screwdriver, remove the four 22-mm torx screws holding the back panel in place.

Step 4

  • Use the edge of the spudger to loosen and remove the back panel.

Use the edge of the spudger to loosen and remove the back panel.

Step 5

  • Remove the single 20-mm torx screw holding the rear panel in place.

Remove the single 20-mm torx screw holding the rear panel in place.

Step 6

  • Pull back the rear side of the back panel.

Pull back the rear side of the back panel.

Step 7

              Power Switch
  • There is an inner plastic guard behind the motor shaft.
  • Unscrew the four screws at each corner.
  • The guard should pull out with a good firm tug.

There is an inner plastic guard behind the motor shaft.

Unscrew the four screws at each corner.

The guard should pull out with a good firm tug.

Step 8

  • Just behind the inner guard is the button slide.
  • Use needle nose pliers to pinch and push the button’s flanges together, and out of the slot.

Just behind the inner guard is the button slide.

Use needle nose pliers to pinch and push the button’s flanges together, and out of the slot.

Step 9

  • Using the J-1 screwdriver, unscrew the power cord wires from the red switch box (located in the back of the grinder).

Using the J-1 screwdriver, unscrew the power cord wires from the red switch box (located in the back of the grinder).

Step 10

  • Disconnect the motor wires from the other side of the switch box.
  • They wires are connected as a sleeve to the flat pin out of the switch box. A firm pull should do it.

Disconnect the motor wires from the other side of the switch box.

They wires are connected as a sleeve to the flat pin out of the switch box. A firm pull should do it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors 


                    Kean Wee

Member since: 01/22/2015

468 Reputation

                                      4 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team 18-6, Maness Winter 2015                        

                                                  Member of Cal Poly, Team 18-6, Maness Winter 2015 



                    CPSU-MANESS-W15S18G6                     


                                            5 Members                     


                                            7 Guides authored

Michael Creel - Nov 5, 2017

Reply

Very clear and concise guide with relevent pictures. Very well done, thank you