Desktop Pc Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 30 minutes

Sections

Left Panel
2 steps
Right Panel
2 steps
Graphics Card
2 steps
Hard Drive
4 steps
Motherboard
3 steps

Flags

Missed a Step

Oops! This guide is currently missing some important steps.

BackDesktop Computer
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Left Panel

Unplug the computer from the power supply before any maintenance or disassembly.
Remove the two Phillips #2 head 5mm screws from the back side of the computer case. You only need to remove the screws that hold down the panel.
These screws can usually be removed by hand.
Be sure to wear an anti-static bracelet or use an anti-static mat to ensure important components are not damaged by static electricity.

Unplug the computer from the power supply before any maintenance or disassembly.

Remove the two Phillips #2 head 5mm screws from the back side of the computer case. You only need to remove the screws that hold down the panel.

These screws can usually be removed by hand.

Be sure to wear an anti-static bracelet or use an anti-static mat to ensure important components are not damaged by static electricity.

1024

Step 2

Next, remove the side panel of the computer case to allow access into the computer. Slide the panel towards the back of the computer and lift it up to remove.
If there is a fan mounted on the side panel, make sure to unplug the cable before fully removing the panel.

Next, remove the side panel of the computer case to allow access into the computer. Slide the panel towards the back of the computer and lift it up to remove.

If there is a fan mounted on the side panel, make sure to unplug the cable before fully removing the panel.

Step 3

              Right Panel

Remove two Phillips #2 head 5mm screws from the back side of the computer case.

Remove two Phillips #2 head 5mm screws from the back side of the computer case.

Step 4

Next, remove the side panel of the computer case to allow access into the computer.

Next, remove the side panel of the computer case to allow access into the computer.

Step 5

              Graphics Card

Remove the Phillips #2 head, 5mm screw holding the graphics card in place.
Make sure that you have grounded yourself so that upon removal of the graphics card you do not accidentally shock the circuit board and damage it.

Remove the Phillips #2 head, 5mm screw holding the graphics card in place.

Make sure that you have grounded yourself so that upon removal of the graphics card you do not accidentally shock the circuit board and damage it.

Step 6

Press the latch on the side of the connector area to unlock the graphics card, and carefully slide the graphics card out from its slot in the computer.
A good technique is to lay the computer onto it side, push the latch down and lift the graphics card out.

Press the latch on the side of the connector area to unlock the graphics card, and carefully slide the graphics card out from its slot in the computer.

A good technique is to lay the computer onto it side, push the latch down and lift the graphics card out.

Step 7

              Hard Drive

Remove two Phillips #2 head 5mm screws holding the hard drive in place.

Remove two Phillips #2 head 5mm screws holding the hard drive in place.

Step 8

Remove two Phillips #2 head 5mm screws holding in the other side of the hard drive.

Remove two Phillips #2 head 5mm screws holding in the other side of the hard drive.

Step 9

Slide the hard drive out from the metal casing.

Slide the hard drive out from the metal casing.

Step 10

Remove the cables from the back of the hard drive.

Remove the cables from the back of the hard drive.

Step 11

              Motherboard

Begin to disconnect all cables from the motherboard. Many of the cables will have clips that need to be undone before you can remove them from the motherboard.

Begin to disconnect all cables from the motherboard. Many of the cables will have clips that need to be undone before you can remove them from the motherboard.

Step 12

Remove nine Phillips #2 head 5mm screws from the motherboard. Be sure to have your computer on its side, so that once the screws are out nothing falls and gets damaged.

Remove nine Phillips #2 head 5mm screws from the motherboard. Be sure to have your computer on its side, so that once the screws are out nothing falls and gets damaged.

Step 13

Double check and make sure all wires and screws have been removed, then carefully remove the motherboard from the computer case.

Double check and make sure all wires and screws have been removed, then carefully remove the motherboard from the computer case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      101 other people completed this guide.

Author

                                      with 10 other contributors

                    David Lennon

Member since: 04/14/2015

9,695 Reputation

                                      10 Guides authored                  



                       Badges:
                       23







                                                        +20 more badges

Team

                       Cal Poly, Team 4-5, Maness Spring 2015                        

                                                  Member of Cal Poly, Team 4-5, Maness Spring 2015 



                    CPSU-MANESS-S15S4G5                     


                                            4 Members                     


                                            29 Guides authored

Ingmārs Zaicevs - Jan 13, 2018

If you aim to replace just the motherboard, I don’t think removing the hard drive from the case should be neccessary. The point of removing SATA cable from the motherboard still stands.

Scott Sinclair - Aug 1, 2020

Generally a good article for a beginner. Very thorough. I personally do not remove the hard drives or cpu fans as it makes it both faster and easier to hold. Disconnect all the cables and graphics card then unscrew the motherboard screws and you are good to go!

jade kelly - Feb 25, 2021

such great info thanks for sharing with us.great blog

Thapelo - Apr 7, 2022

hey my pc turn on but it doesn’t show on screen.

Simone - Apr 8, 2022

Hi, first thing I would check is video output default settings, so if you have the monitor connected to a dedicated/discreet graphics card try connecting the video cable to the mobo integrated one or viceversa. Otherwise, the fix could be as simple as replacing the BIOS battery (if the motherboard you are using as replacement is an old one) but could also be a hardware failure/compatibility issue, or a missing power cable (do you hear any beep during power-on self-test?), knowing the PC specs would help identify the problem.

Missed a Step#

Introduction#

What you need#

Team#

Missed a Step

Introduction

What you need

Team