Difficulty

Moderate

Steps

9

Time Required

Suggest a time??

Sections

2

  • DeLonghi ESAM 3000.B Magnifica Open
  • 7 steps
  • timing belt
  • 2 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDeLonghi ESAM family of coffee preparing automates

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Note: It is generally sufficient to remove the base plate. However, removing the side panels is not difficult and you will then have better access to the engine.

What you need

Step 1

              Preparations
  • Pull the plug!
  • Remove the drip tray, the water tank and the pulp container.

Pull the plug!

Remove the drip tray, the water tank and the pulp container.

1024

Step 2

              Unscrew the rear panel
  • The rear panel and side panels are attached with six phillips screws #2. Screw them out.

The rear panel and side panels are attached with six phillips screws #2. Screw them out.

Step 3

              Remove right side panel
  • Slide the right side panel about 2 cm to the back.
  • Then solve it.

Slide the right side panel about 2 cm to the back.

Then solve it.

Step 4

              Remove left side panel
  • The left side is a bit stuck. Place a plastic opening tool in the gap between the front and left side panel above the opening for the water tank. Lift the gap slightly larger.
  • Then place the tool in the gap between the front and left side panel under the opening for the water tank. Increase the gap and push the side part about 2 cm to the rear.
  • Lift out the left side piece.

The left side is a bit stuck. Place a plastic opening tool in the gap between the front and left side panel above the opening for the water tank. Lift the gap slightly larger.

Then place the tool in the gap between the front and left side panel under the opening for the water tank. Increase the gap and push the side part about 2 cm to the rear.

Lift out the left side piece.

Step 5

              Remove rear panel
  • Take out the rear panel.

Take out the rear panel.

Step 6

              Unscrew top cover
  • The front panel is secured with four PH2 Phillips screws, two left and one right each. Turn it out.
  • Use a plastic opening tool to lever off the steam tap.
  • Carefully pull the front panel about 1 cm forward so that there is a gap between the top cover and the front panel,
  • Do not pull the front panel too far, it is still attached with different hoses and cables.

The front panel is secured with four PH2 Phillips screws, two left and one right each. Turn it out.

Use a plastic opening tool to lever off the steam tap.

Carefully pull the front panel about 1 cm forward so that there is a gap between the top cover and the front panel,

Do not pull the front panel too far, it is still attached with different hoses and cables.

Step 7

              Remove top cover
  • Two Phillips screws PH2 hold the lid at the back. Turn it out.
  • Lift the lid upwards.

Two Phillips screws PH2 hold the lid at the back. Turn it out.

Lift the lid upwards.

Step 8

              timing belt
  • This is what the timing belt looks like.
  • Lay the machine on its side.
  • The bottom panel is secured with five Torx TR15 security screws. turn them out.
  • Take off the bottom plate. The toothed belt becomes visible.

This is what the timing belt looks like.

Lay the machine on its side.

The bottom panel is secured with five Torx TR15 security screws. turn them out.

Take off the bottom plate. The toothed belt becomes visible.

Step 9

  • It’s easier if you loosen the motor.
  • Remove the four Phillips screws securing the motor. (Two are obscured in the picture). Loosen the motor and push it up a little.
  • Lift off the timing belt.

It’s easier if you loosen the motor.

Remove the four Phillips screws securing the motor. (Two are obscured in the picture). Loosen the motor and push it up a little.

Lift off the timing belt.

Work the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

        HelloMacOS is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

HelloMacOS

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges