Difficulty

Moderate

Steps

10

Time Required

Suggest a time??

Sections

2

  • DeLonghi ESAM 3000.B Magnifica Open
  • 7 steps
  • Grinder
  • 3 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDeLonghi ESAM family of coffee preparing automates

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Preparations
  • Pull the plug!
  • Remove the drip tray, the water tank and the pulp container.

Pull the plug!

Remove the drip tray, the water tank and the pulp container.

1024

Step 2

              Unscrew the rear panel
  • The rear panel and side panels are attached with six phillips screws #2. Screw them out.

The rear panel and side panels are attached with six phillips screws #2. Screw them out.

Step 3

              Remove right side panel
  • Slide the right side panel about 2 cm to the back.
  • Then solve it.

Slide the right side panel about 2 cm to the back.

Then solve it.

Step 4

              Remove left side panel
  • The left side is a bit stuck. Place a plastic opening tool in the gap between the front and left side panel above the opening for the water tank. Lift the gap slightly larger.
  • Then place the tool in the gap between the front and left side panel under the opening for the water tank. Increase the gap and push the side part about 2 cm to the rear.
  • Lift out the left side piece.

The left side is a bit stuck. Place a plastic opening tool in the gap between the front and left side panel above the opening for the water tank. Lift the gap slightly larger.

Then place the tool in the gap between the front and left side panel under the opening for the water tank. Increase the gap and push the side part about 2 cm to the rear.

Lift out the left side piece.

Step 5

              Remove rear panel
  • Take out the rear panel.

Take out the rear panel.

Step 6

              Unscrew top cover
  • The front panel is secured with four PH2 Phillips screws, two left and one right each. Turn it out.
  • Use a plastic opening tool to lever off the steam tap.
  • Carefully pull the front panel about 1 cm forward so that there is a gap between the top cover and the front panel,
  • Do not pull the front panel too far, it is still attached with different hoses and cables.

The front panel is secured with four PH2 Phillips screws, two left and one right each. Turn it out.

Use a plastic opening tool to lever off the steam tap.

Carefully pull the front panel about 1 cm forward so that there is a gap between the top cover and the front panel,

Do not pull the front panel too far, it is still attached with different hoses and cables.

Step 7

              Remove top cover
  • Two Phillips screws PH2 hold the lid at the back. Turn it out.
  • Lift the lid upwards.

Two Phillips screws PH2 hold the lid at the back. Turn it out.

Lift the lid upwards.

Step 8

              Grinder
  • Pull the flat connectors of the two black cables that lead to the grinder from the main circuit board.

Pull the flat connectors of the two black cables that lead to the grinder from the main circuit board.

Step 9

  • The grinder is attached from above with three Phillips screws. The screws are somewhat hidden and you need a long-shafted screwdriver, possibly a flexible drive. Unscrew the three screws.
  • You can also dismantle the bean container beforehand.

The grinder is attached from above with three Phillips screws. The screws are somewhat hidden and you need a long-shafted screwdriver, possibly a flexible drive. Unscrew the three screws.

You can also dismantle the bean container beforehand.

Step 10

  • Lift the grinder up and out. Pay attention to the two black cables.
  • If your spare part does not have a bean container, you still have to transfer it to the new part.

Lift the grinder up and out. Pay attention to the two black cables.

If your spare part does not have a bean container, you still have to transfer it to the new part.

Work the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

        oldturkey03 is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

oldturkey03

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges