Difficulty
Moderate
Steps
11
Time Required
Suggest a time??
Sections
2
- DeLonghi ESAM 3000.B Magnifica Open
- 7 steps
- pressure regulator
- 4 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackDeLonghi ESAM family of coffee preparing automates
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Note: in the guide the top cover of the coffee maker was also removed. If you have no other repairs, this is not absolutely necessary and you can skip the corresponding steps.
What you need
Step 1
Preparations
- Pull the plug!
- Remove the drip tray, the water tank and the pulp container.
Pull the plug!
Remove the drip tray, the water tank and the pulp container.
1024
Step 2
Unscrew the rear panel
- The rear panel and side panels are attached with six phillips screws #2. Screw them out.
The rear panel and side panels are attached with six phillips screws #2. Screw them out.
Step 3
Remove right side panel
- Slide the right side panel about 2 cm to the back.
- Then solve it.
Slide the right side panel about 2 cm to the back.
Then solve it.
Step 4
Remove left side panel
- The left side is a bit stuck. Place a plastic opening tool in the gap between the front and left side panel above the opening for the water tank. Lift the gap slightly larger.
- Then place the tool in the gap between the front and left side panel under the opening for the water tank. Increase the gap and push the side part about 2 cm to the rear.
- Lift out the left side piece.
The left side is a bit stuck. Place a plastic opening tool in the gap between the front and left side panel above the opening for the water tank. Lift the gap slightly larger.
Then place the tool in the gap between the front and left side panel under the opening for the water tank. Increase the gap and push the side part about 2 cm to the rear.
Lift out the left side piece.
Step 5
Remove rear panel
- Take out the rear panel.
Take out the rear panel.
Step 6
Unscrew top cover
- The front panel is secured with four PH2 Phillips screws, two left and one right each. Turn it out.
- Use a plastic opening tool to lever off the steam tap.
- Carefully pull the front panel about 1 cm forward so that there is a gap between the top cover and the front panel,
- Do not pull the front panel too far, it is still attached with different hoses and cables.
The front panel is secured with four PH2 Phillips screws, two left and one right each. Turn it out.
Use a plastic opening tool to lever off the steam tap.
Carefully pull the front panel about 1 cm forward so that there is a gap between the top cover and the front panel,
Do not pull the front panel too far, it is still attached with different hoses and cables.
Step 7
Remove top cover
- Two Phillips screws PH2 hold the lid at the back. Turn it out.
- Lift the lid upwards.
Two Phillips screws PH2 hold the lid at the back. Turn it out.
Lift the lid upwards.
Step 8
pressure regulator
- The old safety valve - seen in the first photo already expanded - is screwed on the pump. It is replaced by a combination of safety valve and pressure balance valve. The diaphragm valve dampens the shocks of the pump, making the flow of water quieter and quieter.
The old safety valve - seen in the first photo already expanded - is screwed on the pump. It is replaced by a combination of safety valve and pressure balance valve. The diaphragm valve dampens the shocks of the pump, making the flow of water quieter and quieter.
Step 9
- Remove the two hoses from the valve. For the thicker hose you have to squeeze the hose clamp with pliers, push it away and you can pull off the hose.
- With the thinner pressure hose above you have to pull out first a clamp, then the hose comes out easily. There may be a gasket on the hose or it may stick in the valve.
Remove the two hoses from the valve. For the thicker hose you have to squeeze the hose clamp with pliers, push it away and you can pull off the hose.
With the thinner pressure hose above you have to pull out first a clamp, then the hose comes out easily. There may be a gasket on the hose or it may stick in the valve.
Step 10
- Pull the pump slightly out of the housing in its rubber mount. Place a fork wrench SW 12 on the pump tube.
- Then turn out the old valve.
Pull the pump slightly out of the housing in its rubber mount. Place a fork wrench SW 12 on the pump tube.
Then turn out the old valve.
Step 11
- Make sure that there is a sealing ring above the thread on the valves, marked yellow in the photo.
- First screw the safety valve into the pump tube. Do not turn too hard.
- then screw the pressure regulating valve into the safety valve.
- Place the two outputs on top of each other.
- Put the two hoses back on. Also pay attention here to the thinner tube on the sealing ring, if possible, a new one.
Make sure that there is a sealing ring above the thread on the valves, marked yellow in the photo.
First screw the safety valve into the pump tube. Do not turn too hard.
then screw the pressure regulating valve into the safety valve.
Place the two outputs on top of each other.
Put the two hoses back on. Also pay attention here to the thinner tube on the sealing ring, if possible, a new one.
Repeat the steps in order to reassemble your device.
Cancel: I did not complete this guide.
2 other people completed this guide.
These translators are helping us fix the world! Want to contribute? Start translating ›
Special thanks to these translators:
100%
irlanda
VauWeh
Author
with 1 other contributor
VauWeh
Member since: 10/19/2015
160,441 Reputation
210 Guides authored
Badges:
41
+38 more badges
SCHLUMPF - Jan 8, 2023
Reply
Sehr gute Anleitung.
Den Deckel abzunehmen fand ich nicht notwendig.
Sehr hilfreich die Ersatzteil Bezugsquellen.
Maschine ist jetzt um einiges leiser.
Danke
VauWeh - Jan 8, 2023
Reply
Gern geschehen. Stimmt, bei dieser Reparatur muss der Deckel nicht unbedingt ab, liegt halt an der Logik dieser aufeinander aufbauenden Anleitungen.
