Difficulty
Easy
Steps
12
Time Required
5 minutes
Sections
4
- Back Cover
- 5 steps
- Battery Disconnection
- 1 step
- Battery
- 4 steps
- Track Pad
- 2 steps
Flags
1
Missed a Step
Oops! This guide is currently missing some important steps.
BackDell XPS 13 (9343/9350)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove the eight 4 mm T5 Torx screws from the bottom cover.
Remove the eight 4 mm T5 Torx screws from the bottom cover.
1024
Step 2
- Use a plastic opening tool to pry open the ‘XPS’ flap in the middle.
Use a plastic opening tool to pry open the ‘XPS’ flap in the middle.
Step 3
- Remove the single Phillips screw hidden beneath the flap.
Remove the single Phillips screw hidden beneath the flap.
Step 4
- Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.
Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.
Step 5
- Remove the bottom cover.
Remove the bottom cover.
Step 6
Battery Disconnection
- Pull the battery cable connector towards the battery to disconnect it from its socket.
- If the connector is stubborn, push a little at one side, then the other, to “walk” it out of its socket.
- If you have trouble walking the connector out of the socket, use the point of a spudger to gently push on the connector indent to slide the connector out.
- Do not pull up.
- Open the display and press the power button for five seconds to drain any remaining charge from the system.
Pull the battery cable connector towards the battery to disconnect it from its socket.
If the connector is stubborn, push a little at one side, then the other, to “walk” it out of its socket.
If you have trouble walking the connector out of the socket, use the point of a spudger to gently push on the connector indent to slide the connector out.
Do not pull up.
Open the display and press the power button for five seconds to drain any remaining charge from the system.
Step 7
Battery
- Remove the four 3 mm Phillips #0 screws located on each corner of the battery.
Remove the four 3 mm Phillips #0 screws located on each corner of the battery.
Step 8
- Pull the battery cable connector towards the battery to disconnect it from its socket.
- Do not pull up.
Step 9
- Peel up any tape securing the speaker cables to the battery.
- You do not need to remove the speakers, only the tape, allowing the battery to be removed out under the speaker cables.
Peel up any tape securing the speaker cables to the battery.
You do not need to remove the speakers, only the tape, allowing the battery to be removed out under the speaker cables.
Step 10
- Remove the battery.
Remove the battery.
Step 11
Track Pad
- Remove the four 3 mm Phillips #1 screws from the trackpad.
Remove the four 3 mm Phillips #1 screws from the trackpad.
Step 12
- Use tweezers to gently lift the upper-right corner of the track pad.
- Remove the track pad by slowly pulling it up and away from you.
Use tweezers to gently lift the upper-right corner of the track pad.
Remove the track pad by slowly pulling it up and away from you.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 3 other contributors
Arvind Krish
Member since: 04/26/2017
179 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
Cal Poly, Team S21-G6, Livingston Spring 2017
Member of Cal Poly, Team S21-G6, Livingston Spring 2017
CPSU-LIVINGSTON-S17S21G6
5 Members
28 Guides authored
