Difficulty

Moderate

Steps

12

Time Required

                          10 - 20 minutes

Sections

2

  • Battery
  • 7 steps
  • Speakers
  • 5 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell XPS 13 9365 2-in-1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Use a Torx T4 screwdriver to remove the eight screws (M2x3) that secure the base cover to the palm-rest assembly.

Use a Torx T4 screwdriver to remove the eight screws (M2x3) that secure the base cover to the palm-rest assembly.

1024

Step 2

  • Use your fingertips to lift the system badge open and reveal the single case screw.
  • Use a Phillips #000 screwdriver to remove the screw (M1.6x4) that secures the base cover to the palm-rest assembly.

Use your fingertips to lift the system badge open and reveal the single case screw.

Use a Phillips #000 screwdriver to remove the screw (M1.6x4) that secures the base cover to the palm-rest assembly.

Step 3

  • Starting from the front corner of the computer, pry up the base cover using a spudger and lift the base cover off the palm-rest assembly.

Starting from the front corner of the computer, pry up the base cover using a spudger and lift the base cover off the palm-rest assembly.

Step 4

  • Disconnect the battery cable from the system board.

Disconnect the battery cable from the system board.

Step 5

  • Use a Phillips #000 screwdriver to remove the two screws (M1.6x4) that secure the battery to the palm-rest assembly.

Use a Phillips #000 screwdriver to remove the two screws (M1.6x4) that secure the battery to the palm-rest assembly.

Step 6

  • Use a Phillips #000 screwdriver to remove the six screws (M2x3) that secure the battery to the palm-rest assembly.

Use a Phillips #000 screwdriver to remove the six screws (M2x3) that secure the battery to the palm-rest assembly.

Step 7

  • Lift the battery off the palm-rest assembly.

Lift the battery off the palm-rest assembly.

Step 8

              Speakers
  • Peel off the tape securing the speaker cable to the system board.

Peel off the tape securing the speaker cable to the system board.

Step 9

  • Disconnect the speaker cable from the motherboard.

Disconnect the speaker cable from the motherboard.

Step 10

  • Note the speaker-cable routing and peel off the tape that secures the speaker cable to the system board.

Note the speaker-cable routing and peel off the tape that secures the speaker cable to the system board.

Step 11

  • Use a Phillips #000 screwdriver to remove the four screws (M2x2) that secure the speakers to the palm-rest assembly.

Use a Phillips #000 screwdriver to remove the four screws (M2x2) that secure the speakers to the palm-rest assembly.

Step 12

  • Lift the speakers, along with its cables, off the palm-rest assembly.

Lift the speakers, along with its cables, off the palm-rest assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Melissa Schlein

Member since: 03/21/2022

567 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       University of Alabama, Team 3-4, Bedsole Spring 2022                        

                                                  Member of University of Alabama, Team 3-4, Bedsole Spring 2022 



                    UA-BEDSOLE-S22S3G4                     


                                            3 Members                     


                                            3 Guides authored