Dell Venue 11 Pro Usb Port Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Battery
2 steps
Frame
7 steps
USB Port
6 steps

Flags

BackDell Venue 11 Pro 7000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Turn your device over to the backside. On the notch at the bottom portion of the tablet, use your fingers to lift up the back cover.

Turn your device over to the backside. On the notch at the bottom portion of the tablet, use your fingers to lift up the back cover.

1024

Step 2

Below the battery pack, there are two lock mechanisms. Push EACH lock to the LEFT until it makes a click noise. Lift the battery from the bottom up and remove.

Below the battery pack, there are two lock mechanisms. Push EACH lock to the LEFT until it makes a click noise. Lift the battery from the bottom up and remove.

Step 3

              Frame

Use your Philips #000 screwdriver to unscrew the fourteen 2.5 mm screws marked on the tablet.
These screws are extremely small. Place the screws aside in a container or on your magnetic mat to prevent accidental loss.

Use your Philips #000 screwdriver to unscrew the fourteen 2.5 mm screws marked on the tablet.

These screws are extremely small. Place the screws aside in a container or on your magnetic mat to prevent accidental loss.

Step 4

Slide the cover on the two middle ribbon cables out to remove it. It should uncover the orange cable connectors.

Slide the cover on the two middle ribbon cables out to remove it. It should uncover the orange cable connectors.

Step 5

To disconnect the left ribbon cable from the motherboard, place the flat end of your spudger under the edge of the pop connector and pry the connector straight up.
The two ribbon cables connect the keyboard attachment ports to the motherboard. Damage to either cables can induce problems with the Dell mobile keyboard.

To disconnect the left ribbon cable from the motherboard, place the flat end of your spudger under the edge of the pop connector and pry the connector straight up.

The two ribbon cables connect the keyboard attachment ports to the motherboard. Damage to either cables can induce problems with the Dell mobile keyboard.

Step 6

The right ribbon cable has a ZIF connector. Use the flat end of your spudger to lift up the small locking flap, then pull out the cable.
Pulling the ribbon cable out before unlocking the connector can potentially damage the cable.

The right ribbon cable has a ZIF connector. Use the flat end of your spudger to lift up the small locking flap, then pull out the cable.

Pulling the ribbon cable out before unlocking the connector can potentially damage the cable.

Step 7

There are adhesive strips between the device and the two ribbon cables we disconnected. Pull each cable away from the device just enough to break the adhesive bonds.

There are adhesive strips between the device and the two ribbon cables we disconnected. Pull each cable away from the device just enough to break the adhesive bonds.

Step 8

Use your pin punch driver to push into the hole on the sim card, then pull out the sim tray.

Use your pin punch driver to push into the hole on the sim card, then pull out the sim tray.

Step 9

Insert your plastic opening tool between the screen and frame, and run the tool around the edges to separate the frame from the tablet.

Insert your plastic opening tool between the screen and frame, and run the tool around the edges to separate the frame from the tablet.

Step 10

              USB Port

Start by removing the top ZIF USB ribbon connector
If you are replacing the motherboard by itself, then skip steps 23, 24, and 25.

Start by removing the top ZIF USB ribbon connector

If you are replacing the motherboard by itself, then skip steps 23, 24, and 25.

Step 11

To remove the ribbon cable, move the black retainer upwards. Then pull the ribbon cable rearwards to remove it.

To remove the ribbon cable, move the black retainer upwards. Then pull the ribbon cable rearwards to remove it.

Step 12

You must then remove the ribbon cable connected to the USB port located here.

You must then remove the ribbon cable connected to the USB port located here.

Step 13

Using a Philips #000 screwdriver remove the two 2.5 mm screws indicated.

Using a Philips #000 screwdriver remove the two 2.5 mm screws indicated.

Step 14

Using a pair of tweezers disconnect the connector from the circuit board

Using a pair of tweezers disconnect the connector from the circuit board

Step 15

After disconnecting all the pieces, remove the USB port circuit board with your fingers

After disconnecting all the pieces, remove the USB port circuit board with your fingers

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 4 other contributors

                    Tom Nguyen

Member since: 09/28/2017

1,277 Reputation

                                      6 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       USF Tampa, Team S3-G1, Nance Fall 2017                        

                                                  Member of USF Tampa, Team S3-G1, Nance Fall 2017 



                    USFT-NANCE-F17S3G1                     


                                            4 Members                     


                                            8 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team