Dell Streak 10 Pro Speakers Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes

Sections

Battery
4 steps
SD Card Breakout Board
4 steps
Speakers
11 steps

Flags

BackDell Streak 10 Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Place the device flat on its screen.
Using the plastic opening tools, pry open the top segment of the tablet where the camera is located.
Take the segment off and place it to the side.

Place the device flat on its screen.

Using the plastic opening tools, pry open the top segment of the tablet where the camera is located.

Take the segment off and place it to the side.

1024

Step 2

Remove four 4mm Phillips #0 screws.

Remove four 4mm Phillips #0 screws.

Step 3

Using the plastic opening tool, lift off the entire back screen of the tablet.

Using the plastic opening tool, lift off the entire back screen of the tablet.

Step 4

Disconnect the no-fuss ribbon cable connector.
The best way is to safely pull the white connector straight out of the socket. Using the tweezers, pull out the white connector that contains the red, green, blue, and black cords connected to it.
Remove the battery by gently lifting it out of the device.

Disconnect the no-fuss ribbon cable connector.

The best way is to safely pull the white connector straight out of the socket. Using the tweezers, pull out the white connector that contains the red, green, blue, and black cords connected to it.

Remove the battery by gently lifting it out of the device.

Step 5

              SD Card Breakout Board

Remove three 4mm Phillips #0 screws.

Remove three 4mm Phillips #0 screws.

Step 6

Gently lift up the black covered wire and place it on the side, so that it is not in the way of the procedure.

Gently lift up the black covered wire and place it on the side, so that it is not in the way of the procedure.

Step 7

When encountering a zero insertion force connector, the best way it to carefully use tweezers to flip up the white locking flap securing the blue-tipped ribbon cable.
Then, gently use the tweezers to pull out the blue-tipped ribbon cable from the unlatched connector.

When encountering a zero insertion force connector, the best way it to carefully use tweezers to flip up the white locking flap securing the blue-tipped ribbon cable.

Then, gently use the tweezers to pull out the blue-tipped ribbon cable from the unlatched connector.

Step 8

Use two fingers and gently pull the SD card breakout board from its space.

Use two fingers and gently pull the SD card breakout board from its space.

Step 9

              Speakers

There are five ribbon cables in a row that must be disconnected.
Using the tweezers, carefully pull out the first cable straight out of the no-fuss ribbon cable connector.

There are five ribbon cables in a row that must be disconnected.

Using the tweezers, carefully pull out the first cable straight out of the no-fuss ribbon cable connector.

Step 10

Using the tweezers, carefully pull out the cable straight out of the no-fuss ribbon cable connector.

Using the tweezers, carefully pull out the cable straight out of the no-fuss ribbon cable connector.

Step 11

When dealing with a zero insertion force connector, the best way it to carefully use a tweezer to flip up the white locking flap holding the blue-tipped ribbon cable.
Then, gently remove the ribbon cable from the socket.

When dealing with a zero insertion force connector, the best way it to carefully use a tweezer to flip up the white locking flap holding the blue-tipped ribbon cable.

Then, gently remove the ribbon cable from the socket.

Step 12

When dealing with a zero insertion force connector, the best way it to carefully use a tweezer to flip up the white locking flap holding the blue tip wire.
Then gently remove the wire from the socket.

When dealing with a zero insertion force connector, the best way it to carefully use a tweezer to flip up the white locking flap holding the blue tip wire.

Then gently remove the wire from the socket.

Step 13

Carefully remove the adhesive tapes using the tweezers.

Carefully remove the adhesive tapes using the tweezers.

Step 14

Using the tweezers, carefully flip up the locking tab on the Zero Insertion Force connector.
Then, gently disconnect the orange ribbon cable.

Using the tweezers, carefully flip up the locking tab on the Zero Insertion Force connector.

Then, gently disconnect the orange ribbon cable.

Step 15

After removing all the adhesive strips, gently lift up the sensor board as to not bend it.

After removing all the adhesive strips, gently lift up the sensor board as to not bend it.

Step 16

When dealing with a zero insertion force connector, the best way it to carefully use a tweezer to flip up the white locking flap holding the orange ribbon cable.
Once the white tab is lifted, use the tweezer to carefully pull out the orange ribbon cable.

When dealing with a zero insertion force connector, the best way it to carefully use a tweezer to flip up the white locking flap holding the orange ribbon cable.

Once the white tab is lifted, use the tweezer to carefully pull out the orange ribbon cable.

Step 17

Using your fingers, wiggle the speaker until it comes free from the device. Carefully remove it from the tablet.

Using your fingers, wiggle the speaker until it comes free from the device. Carefully remove it from the tablet.

Step 18

Using your fingers, wiggle the other speaker until it comes free. Carefully remove it from the tablet.

Using your fingers, wiggle the other speaker until it comes free. Carefully remove it from the tablet.

Step 19

Carefully pull out the connected speakers.

Carefully pull out the connected speakers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Matthew Ko

Member since: 02/05/2019

440 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UC Davis, Team S20-G7, Lore Winter 2019                        

                                                  Member of UC Davis, Team S20-G7, Lore Winter 2019 



                    UCD-LORE-W19S20G7                     


                                            2 Members                     


                                            4 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team