Dell Optiplex Fx170 Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Case
4 steps
RAM
2 steps
Memory Board
1 step
CMOS Battery
1 step
Motherboard
4 steps

Flags

BackDell OptiPlex FX170
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Case

With the base stand facing upwards, unscrew the 6mm Phillips #2 screw.
Pull the base stand straight up from the device.

With the base stand facing upwards, unscrew the 6mm Phillips #2 screw.

Pull the base stand straight up from the device.

1024

Step 2

Unscrew and remove the eight 4mm Phillips #0 screws (four on top, four on bottom) from the top and bottom of the device.

Unscrew and remove the eight 4mm Phillips #0 screws (four on top, four on bottom) from the top and bottom of the device.

Step 3

Run the flat side of the spudger along the entire line of the case starting from the back where the power plug and a small screw are located.
Use care to not apply excessive force that could damage retaining clips while running the spudger along the case.

Run the flat side of the spudger along the entire line of the case starting from the back where the power plug and a small screw are located.

Use care to not apply excessive force that could damage retaining clips while running the spudger along the case.

Step 4

Once the clips have been released, gently disengage the cover from the rest of case by pulling in opposite directions.

Once the clips have been released, gently disengage the cover from the rest of case by pulling in opposite directions.

Step 5

RAM

Using fingers, push the clips on either side of the RAM. The RAM will pop up at a 45 degree angle when both clips are disengaged.

Using fingers, push the clips on either side of the RAM. The RAM will pop up at a 45 degree angle when both clips are disengaged.

Step 6

Lift and pull out the RAM.

Lift and pull out the RAM.

Step 7

              Memory Board

Using the spudger, gently push on the underside of the memory board to loosen it. Gently grasp each side and pull up to release the memory board.

Using the spudger, gently push on the underside of the memory board to loosen it. Gently grasp each side and pull up to release the memory board.

Step 8

              CMOS Battery

To remove the battery, pull up on the connector that is plugged into the motherboard.

To remove the battery, pull up on the connector that is plugged into the motherboard.

Step 9

              Motherboard

Remove the two 4mm Phillips #00 screws that are along the back of the case.

Remove the two 4mm Phillips #00 screws that are along the back of the case.

Step 10

Remove the two foam bumpers that lie on top of the two front USB ports with fingers. Do not throw them away.

Remove the two foam bumpers that lie on top of the two front USB ports with fingers. Do not throw them away.

Step 11

Disconnect the speaker cable from the motherboard by gently pulling it straight up to disengage it from the port.
Remove the four 4mm Philips #0 screws that secure the motherboard to the case.
The screw in the corner where the RAM is located is covered by a small piece of Mylar tape, peel this tape back to reveal the screw. The tweezers can be helpful for this.

Disconnect the speaker cable from the motherboard by gently pulling it straight up to disengage it from the port.

Remove the four 4mm Philips #0 screws that secure the motherboard to the case.

The screw in the corner where the RAM is located is covered by a small piece of Mylar tape, peel this tape back to reveal the screw. The tweezers can be helpful for this.

Step 12

Gently grasp the motherboard by the heat sink (the black finned piece). Lift the motherboard at an angle such that the ports along the back side come up first.
Continue lifting the motherboard, then slowly tilt the piece off to the right to break the Mylar tape over the front USB ports.
Be careful when handling the motherboard to prevent electro-static discharge (ESD) damage. If the motherboard is being removed as part of a prerequisite, place the motherboard into a bag designed to prevent a build up of a static charge (usually referred to as a static bag).

Gently grasp the motherboard by the heat sink (the black finned piece). Lift the motherboard at an angle such that the ports along the back side come up first.

Continue lifting the motherboard, then slowly tilt the piece off to the right to break the Mylar tape over the front USB ports.

Be careful when handling the motherboard to prevent electro-static discharge (ESD) damage. If the motherboard is being removed as part of a prerequisite, place the motherboard into a bag designed to prevent a build up of a static charge (usually referred to as a static bag).

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Frank Pecka

Member since: 01/13/2015

340 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Eastern Washington University, Team 1-4, Carnegie Winter 2015                        

                                                  Member of Eastern Washington University, Team 1-4, Carnegie Winter 2015 



                    EWU-CARNEGIE-W15S1G4                     


                                            3 Members                     


                                            13 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team