Difficulty
Moderate
Steps
6
Time Required
10 minutes
Sections
1
- LCD Screen Assembly
- 6 steps
Flags
0
BackDell Latitude E6510
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
LCD Screen Assembly
- Orient your laptop so that the bottom is facing up towards you.
- Place your thumbs on the grooved sections above the battery and firmly pull away from each other.
- Slide the battery out and separate it from the laptop.
Orient your laptop so that the bottom is facing up towards you.
Place your thumbs on the grooved sections above the battery and firmly pull away from each other.
Slide the battery out and separate it from the laptop.
1024
Step 2
- Remove the 5 screws from the back panel with a type 0 Philips head.
- Then pull the panel towards you in a slightly upwards motion.
- Separate the panel from the laptop.
Remove the 5 screws from the back panel with a type 0 Philips head.
Then pull the panel towards you in a slightly upwards motion.
Separate the panel from the laptop.
Step 3
- Take the silver panels from both sides of the back of the laptop by removing the screw using a type 0 Philips head.
- Slide the silver panel away from you to revel some wires.
- Remove the two wires white and gray by gently pulling up and detaching them.
- After the wires are detached, gently pull the wires away from you to remove them from the groove they are in.
Take the silver panels from both sides of the back of the laptop by removing the screw using a type 0 Philips head.
Slide the silver panel away from you to revel some wires.
Remove the two wires white and gray by gently pulling up and detaching them.
After the wires are detached, gently pull the wires away from you to remove them from the groove they are in.
Step 4
- Under the ride silver panel, there is a channel. To disconnect gently use your nail and flick it up and to the right.
- Once the channel is disconnect, there are two wires. Repeat the same method as the channel to disconnect the wires.
- Move the channel and wires out of the groove to remove the screen.
Under the ride silver panel, there is a channel. To disconnect gently use your nail and flick it up and to the right.
Once the channel is disconnect, there are two wires. Repeat the same method as the channel to disconnect the wires.
Move the channel and wires out of the groove to remove the screen.
Step 5
- Orient the laptop on its side, prop it slightly open to keep it stable on your desk.
- Unscrew the silver screw on the left side using a type 0 Phillip’s head.
- Unscrew the black screw on the right side using a type 0 Philips head.
Orient the laptop on its side, prop it slightly open to keep it stable on your desk.
Unscrew the silver screw on the left side using a type 0 Phillip’s head.
Unscrew the black screw on the right side using a type 0 Philips head.
Step 6
- Since the screws and wires are disconnect, the screen is ready to be disconnected also.
- Gently hold the LCD screen with your pointer fingers on either side.
- While firmly holding the bottom of the laptop with your thumbs pull the two parts away from each other.
Since the screws and wires are disconnect, the screen is ready to be disconnected also.
Gently hold the LCD screen with your pointer fingers on either side.
While firmly holding the bottom of the laptop with your thumbs pull the two parts away from each other.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 3 other contributors
haileysobota
Member since: 02/05/2019
205 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
The Citadel Military College of South Carolina, Team S2-G1, Eggleston Spring 2019
Member of The Citadel Military College of South Carolina, Team S2-G1, Eggleston Spring 2019
CMCSC-EGGLESTON-S19S2G1
3 Members
3 Guides authored
