Difficulty
Moderate
Steps
10
Time Required
30 minutes - 1 hour
Sections
1
- Speakers
- 10 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackDell Latitude E6330
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Removing Battery and Hard Drive
- Take out the battery by pulling the tabs.
- Unscrew 2 screws and remove the hard drive (Phillips Head 1 2.5mm x 5mm).
Take out the battery by pulling the tabs.
Unscrew 2 screws and remove the hard drive (Phillips Head 1 2.5mm x 5mm).
1024
Step 2
Removing SD Card and DVD Drive
- Press and remove the SD card protector.
- Press and remove the pull tab on DVD Drive.
Press and remove the SD card protector.
Press and remove the pull tab on DVD Drive.
Step 3
Removing the Backplate
- Unscrew the five screws (Phillips Head 1 2.5mm x 5mm).
- Remove the backplate by pulling from the battery to the front.
Unscrew the five screws (Phillips Head 1 2.5mm x 5mm).
Remove the backplate by pulling from the battery to the front.
Step 4
Removing the Keyboard Bezel
- Remove the track pad wire by carefully pulling up.
- Flip the laptop over to top.
- Remove the bezel from the keyboard by prying under the bezel and unclipping it.
- Pull the bezel from the track pad to the screen to remove it.
- The wire is fragile, handle with care.
Remove the track pad wire by carefully pulling up.
Flip the laptop over to top.
Remove the bezel from the keyboard by prying under the bezel and unclipping it.
Pull the bezel from the track pad to the screen to remove it.
The wire is fragile, handle with care.
Step 5
Keyboard and Trackpad Removal
- Unscrew the three screws (Phillips Head 1 2mm x 3mm).
- Unclip the keyboard wire harness, then slide the wire towards the screen to remove it.
- Unclip the trackpad wire harness, sliding the wire towards the front of the laptop to remove it.
- The wire harnesses are fragile and may break if the user adds too much pressure.
Unscrew the three screws (Phillips Head 1 2mm x 3mm).
Unclip the keyboard wire harness, then slide the wire towards the screen to remove it.
Unclip the trackpad wire harness, sliding the wire towards the front of the laptop to remove it.
The wire harnesses are fragile and may break if the user adds too much pressure.
Step 6
Removing LEDs and Screws
- Grab the wire harness and pull towards the track pad to remove it.
- Remove the six screws (Phillips Head 1 2.5mm x 5mm).
- Remove the two screws (Phillips Head 1 2mm x 3mm).
Grab the wire harness and pull towards the track pad to remove it.
Remove the six screws (Phillips Head 1 2.5mm x 5mm).
Remove the two screws (Phillips Head 1 2mm x 3mm).
Step 7
Removing Back-Palmrest Screws
- Remove the nine screws labeled P (Phillips Head 1 2.5 x 5mm).
- Remove the two screws (Phillips Head 1 2 x 3mm).
Remove the nine screws labeled P (Phillips Head 1 2.5 x 5mm).
Remove the two screws (Phillips Head 1 2 x 3mm).
Step 8
Remove the Palmrest
- Insert spudger tool into crease of palmrest, prying in a downward motion.
- Move along the edges of the palmrest, relieving all clips from laptop base.
- Remove palmrest in a upwards motion.
Insert spudger tool into crease of palmrest, prying in a downward motion.
Move along the edges of the palmrest, relieving all clips from laptop base.
Remove palmrest in a upwards motion.
Step 9
Removing the Speaker Wire
- Remove the four screws to the speakers (Phillips Head 1 2.5 x 7mm).
- Remove the speaker wire harness. Pull towards the track pad to remove it.
- the wire is fragile, pull with care.
Remove the four screws to the speakers (Phillips Head 1 2.5 x 7mm).
Remove the speaker wire harness. Pull towards the track pad to remove it.
the wire is fragile, pull with care.
Step 10
Removing the Speakers
- Remove or move tape out of the way in order to release the wire.
- Remove the speakers.
Remove or move tape out of the way in order to release the wire.
Remove the speakers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Phillip Nguyen
Member since: 05/22/2019
211 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
University of Advancing Technology, Team S1-G8, Beam Summer 2019
Member of University of Advancing Technology, Team S1-G8, Beam Summer 2019
Community
2 Members
1 Guide authored
