Difficulty

Moderate

Steps

15

Time Required

                          20 - 30 minutes

Sections

6

  • Base Panel
  • 2 steps
  • Speakers
  • 2 steps
  • Fan
  • 2 steps
  • USB and Headphone Jack Replacement
  • 3 steps
  • Battery
  • 2 steps
  • Motherboard
  • 4 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackDell Latitude 9510

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Base Panel
  • Flip the device so that the base plate is facing you.
  • Use a Phillips #0 screwdriver to remove the nine 5.5 mm screws securing the base plate.

Flip the device so that the base plate is facing you.

Use a Phillips #0 screwdriver to remove the nine 5.5 mm screws securing the base plate.

1024

Step 2

  • Wedge a spudger between the base plate and the chassis, then gently pry around the entire perimeter to release the base plate.
  • Remove the base plate.

Wedge a spudger between the base plate and the chassis, then gently pry around the entire perimeter to release the base plate.

Remove the base plate.

Step 3

              Speakers
  • Use a Phillips #0 screwdriver to remove the four 2 mm screws from the speakers.

Use a Phillips #0 screwdriver to remove the four 2 mm screws from the speakers.

Step 4

  • Use a spudger to gently lever the speaker connector out of its port.
  • Lift the speakers up and out.

Use a spudger to gently lever the speaker connector out of its port.

Lift the speakers up and out.

Step 5

              Fan
  • Use a Phillips #0 screwdriver to remove the two 3 mm screws securing the fan.

Use a Phillips #0 screwdriver to remove the two 3 mm screws securing the fan.

Step 6

  • Place your fingernails behind the plastic tabs on the speaker’s motherboard connector, then pull directly backwards, toward the wires, until the connector releases from its port.
  • Lift the fan up and out.

Place your fingernails behind the plastic tabs on the speaker’s motherboard connector, then pull directly backwards, toward the wires, until the connector releases from its port.

Lift the fan up and out.

Step 7

              USB and Headphone Jack Replacement
  • Use a Phillips #0 screwdriver to remove the four 3.5 mm screws.

Use a Phillips #0 screwdriver to remove the four 3.5 mm screws.

Step 8

  • Place your fingernails behind each of the plastic tabs on the plug, and pull directly backward until the connector releases.

Place your fingernails behind each of the plastic tabs on the plug, and pull directly backward until the connector releases.

Step 9

  • Flip up the locking bars on the two ZIF connectors so they stand vertically, then gently remove the two ribbon cables connected to the IO daughterboard.
  • Lift the IO daughterboard up and out.

Flip up the locking bars on the two ZIF connectors so they stand vertically, then gently remove the two ribbon cables connected to the IO daughterboard.

Lift the IO daughterboard up and out.

Step 10

              Battery
  • Use a Phillips #0 screwdriver to remove the eight screws securing the battery.

Use a Phillips #0 screwdriver to remove the eight screws securing the battery.

Step 11

  • Place a spudger behind a plastic tab on either side of the plug, then “walk” the connector out of its socket by gently pushing the plug toward the cables, alternating sides, until the connector releases.
  • Lift the battery up and out.

Place a spudger behind a plastic tab on either side of the plug, then “walk” the connector out of its socket by gently pushing the plug toward the cables, alternating sides, until the connector releases.

Lift the battery up and out.

Step 12

              Motherboard
  • Use a Phillips #00 screwdriver to remove the four screws.
  • Use a Phillips #00 screwdriver to remove the three screws.

Use a Phillips #00 screwdriver to remove the four screws.

Use a Phillips #00 screwdriver to remove the three screws.

Step 13

  • Flip up the small metal display cable clip, until the clip is parallel to the ribbon cable, then pull it directly backwards until it releases.
  • Flip up the lock-bar on the ZIF connector, then gently pull the ribbon cable until it releases.
  • This requires almost no force.

Flip up the small metal display cable clip, until the clip is parallel to the ribbon cable, then pull it directly backwards until it releases.

Flip up the lock-bar on the ZIF connector, then gently pull the ribbon cable until it releases.

This requires almost no force.

Step 14

  • Use a Phillips #00 screwdriver to remove the seven 4.0 mm screws.
  • Use a Phillips #00 screwdriver to remove the two 4.5mm screws.

Use a Phillips #00 screwdriver to remove the seven 4.0 mm screws.

Use a Phillips #00 screwdriver to remove the two 4.5mm screws.

Step 15

  • Lift the motherboard up and out.

Lift the motherboard up and out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Adam Sholar

Member since: 02/08/2022

243 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Western Carolina University, Team 1-5, Virtue Spring 2022                        

                                                  Member of Western Carolina University, Team 1-5, Virtue Spring 2022 



                    WCU-VIRTUE-S22S1G5                     


                                            4 Members                     


                                            4 Guides authored